强化两相混合的超临界技术制备聚乳酸微粒

针对商品化聚乳酸微球粒径分布较宽难于适用气溶胶给药要求的不足,采用水力空化混合强化超临界流体辅助雾化技术(SAA-HCM)制备聚乳酸(PLA)超细微粒.该技术主要特点是通过在超临界流体和液相进料处引入水力空化混合器,强化两相间的混合.考察SAA-HCM过程混合器压力、温度、沉淀器温度、进料中CO2与液体溶液质量流量比和溶液质量浓度等操作参数对微粒形态和粒径分布的影响,成功制备出球形度较好,粒径分布较窄(1～3μm)的PLA微球.经X射线衍射(XRD)分析和差示扫描量热(DSC)分析显示,与原料PLA相比,微球晶型及热曲线变化不大,但结晶度下降.同时把操作参数与相行为进行关联,探讨了影响颗粒形貌的机理.对比超临界流体辅助雾化法(SAA)的实验结果表明:水力空化的引入能有效强化混合器内的两相传质,混合更好,能制备出适用于气溶胶给药要求的超细微粒.     

Pilot proteomic analysis of cerebrospinal fluid in Alzheimer's disease

Proteomic analysis of cerebrospinal fluid (CSF) holds great promise in understanding the progression of neurodegenerative diseases, including Alzheimer's disease (AD). As one of the primary reservoirs of neuronal biomolecules, CSF provides a window into the biochemical and cellular aspects of the neurological environment. CSF can be drawn from living participants allowing the potential alignment of clinical changes with these biochemical markers. Using cutting-edge mass spectrometry technologies, we perform a streamlined proteomic analysis of CSF. We quantify greater than 700 proteins across 10 pairs of age- and sex-matched participants in approximately one hour of analysis time each. Using the paired participant study structure, we identify a small group of biologically relevant proteins that show substantial changes in abundance between cognitive normal and AD participants, which were then analyzed at the peptide level using parallel reaction monitoring experiments. Our findings suggest the utility of fractionating a single sample and using matching to increase proteomic depth in cerebrospinal fluid, as well as the potential power of an expanded study.     

Effects of expanding zone parameters of vacuum dust suction mouth on flow simulation results

Based on the parametric analysis of the expanding zone of the vacuum dust suction mouth, the flow in the vacuum dust suction mouth was simulated by computational fluid dynamics （CFD） software, Fluent. The effects of the expanding zone parameters on flow simulation were analyzed. The results show that simulation effects depend on threshold values of the expanding zone parameters of the dust suction mouth, and the threshold values of the expanding zone can be obtained according to the different structures of the vacuum dust suction mouth and be selected as the geometric parameters in calculating, and also corners of the expanding zone make unobvious difference in calculation accuracy and in computational efficiency compared with no corner. The simulation results provide practical guidance to the flow simulation on the dust suction mouth.     

基于表面反应和扩散迁移控制的灰岩单裂隙渗流—溶解模型及其数值模拟

针对碳酸盐类可溶岩地区水电站坝址流场、化学场以及固相介质属性等随时间发生改变,从而对工程安全运行造成不利影响等问题,研究了灰岩地区地下水运移过程中各物理场间的相互作用,分析了影响灰岩溶解速率的两个因素,即表面反应控制和扩散迁移控制。在此基础上,建立了单裂隙中的渗流—溶解耦合模型,并进行数值求解。模拟结果表明,在垂直裂隙延伸方向,其溶蚀锋面为非齐整平面,而是呈似“虫洞”状非均一变化,而沿裂隙延伸方向即自上游侧向下游方向溶蚀程度逐渐减轻;而通过裂隙的流量呈现随时间逐渐增大的趋势,但变幅不大;根据流量求得的等效水力隙宽,其增幅和增长速率均小于实际平均隙宽;同时,化学场中Ca2+浓度的分布与裂隙开度变化具有相似性,不同时刻下上游侧反应速率R均大于下游侧。就反应机制而言,在初期均受表面反应控制,而随反应进行,位于上游补给区部位转为受扩散迁移控制,但在下游位置仍受表面反应控制。     

利用金属络合物的电火花加工研究

在电火花加工的工作液中添加络合剂，使之与被蚀除的金属颗粒产生络合化学反应，生成可溶于工作液中的络合物。利用这种原理，可提高电火花加工性能，在小孔、深槽等加工应用中起到促进排屑的作用。     

A computational fluid dynamic analysis of gas and particle flow in flame spraying

The flame spraying process, which is a common industrial thermal spraying application, has been analyzed by means of three-dimensional computational fluid dynamics (CFD) simulations. The process used at the Volvo Aero Corporation for the coating of fan and compressor housings has been modeled. The process uses the Metco 6P torch (Metco, Westbury, NY), which ejects a mixture of acetylene and oxygen at high speed through a ring of 16 orifices to form the flame. A stream of argon gas flowing through an orifice in the center of the ring carries a powder of nickel-covered bentonite through the flame to the spray substrate. The torch is cooled by a flow of air through an outer ring of 9 orifices. The simulation emulated reality closely by including the individual inlets for fuel, cooling air, and injected particles. The gas combustion was simulated as a turbulent, multicomponent chemically reacting flow. The standard, two-equation k-ε turbulence model was used. The chemical reaction rates appeared as source terms in the species transport equations. They were computed from the contributions of the Arrhenius rate expressions and the Magnussen and Hjertager eddy dissipation model. The first simulations included several intermediate chemical substances whose predicted concentration agreed favorably with measurements. Later, more simplified simulations incorporated only the global chemical reaction involving the initial and the final products, with corrections to the thermal properties being made to account for the missing intermediaries. The gas velocity and temperature fields predicted by the later simulations compared satisfactorily to those predicted by the earlier, more elaborate, ones. Therefore, the final simulations, which incorporated injected particles, were conducted employing the simplified model with only the global reaction. An in-house finite difference code was developed to calculate particle properties. Allowance was made for elliptical shapes, phase changes, and internal heat transfer with regard to the composite material. The particle velocities and temperatures predicted by the final simulations compared fairly well with experimental results obtained with the optical DPV2000 system.     

比较5-Cl-PADAB光度测定Pt(Ⅳ)时的几种活化剂

比较了不同活化剂(KI-Vit C,KI,Vit C,KI-Na_2SO_3,Na_2SO_3,H_2C_2O_4)对5-Cl-PADAB光度测定Pt(Ⅳ)的影响。实验表明,KI、KI-Vit C、KI-Na_2SO_3这3种活化体系最好。其优点为:测定酸度较高,重现性和线性关系好,是良好的活化剂。     

国内外不锈钢精炼剂研究发展现状

分析了精炼剂组元元素的作用能力，讨论并总结了精炼剂组元的复合作用，介绍了几种国内、国外精炼剂产品，提出发展高效复合精炼剂的想法。     

离心铸造大口径球铁管用复合功能型脱硫剂的研制

为使硫量波动的高炉铁液能适应大型离心铸造球铁铸管生产,研制了一种成本较低廉、添加操作简单的复合功能型脱硫剂。其主要组分包括强脱[S]去[O]材料钝化镁粒、碳化钙,增加石墨核心元素Zn和膨胀集渣材料珍珠岩,以及能抑制反球化作用和净化铁液的材料等。采用冲入法进行球化处理,这种脱硫剂覆盖在球化剂和孕育剂上,使用方法简单,效果良好。     

曲轴斜油孔钻削头设计

曲轴的各轴颈在很高的比压下作高速旋转运动,使轴颈和轴承受到强烈磨擦.为保证曲轴轴承工作可靠,曲轴上必须设置可靠的润滑油道,将润滑油送到轴承磨擦表面上去.此油道属细长孔,且于轴线成一定的角度.本文介绍的是一种曲轴斜油孔钻削头的设计、结构和原理等,动用了两个电磁离合器,使得一根钻削头在工作时,另一根钻削头停止旋转,避免不必要的空转功率消耗;该设备用于生产后,实践证明,运行可靠,操作方便,满足了生产需要.