Municipal solid waste conversion to energy

In recent years it has been recognised by an increasing number of nations that there is considerable energy potential within MSW. As a result many countries have established R,D& D programmes to examine methods of exploiting this potential. The IEA's MSW Conversion Activity was set up in 1986 to provide an infrastructure for sharing information and co-ordinating work in this area internationally. This Activity was extended in 1989 and currently a total of 9 nations participate in it.

To cope with the wide scope of the area (encompassing both biological and thermal processing of MSW) the Activity was divided into three subgroups or Expert Working Groups (EWGs). Each of these dealt with a distinct area of expertise:

1. •Downstream effects of source separation and screening of MSW

2. •Sampling and analytical protocols

3. •Landfill gas

In addition to these groups a central secretariat based at Harwell (UK) has provided guidance, established and administered databases of contacts and produced a series of national reports.

This paper describes the achievements of the Activity and discusses work proposed for the future.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Energy efficiency, carbon emissions and economic development in Venezuela

Venezuela's vast natural resource base has largely shaped the nation's economic and energy-use patterns. Major opportunities exist for improving the efficiency of energy use in Venezuela and, consequently, restraining the growth of energy-related carbon emissions. This paper presents a detailed report of one potential development path for Venezuela and estimates the ensuing levels of energy demand and CO₂ emissions associated with pursuing this path through the year 2025. The results indicate that by adopting a development strategy that incorporates structural changes in the economy, fuel-switching measures and improved end-use efficiencies, Venezuela can introduce energy efficiency and carbon restraints as part of its economic development process.     

Policies to reduce energy use and carbon emissions in the UK

The UK differs from may other industrialized nations in that its carbon dioxide (CO₂) emissions from energy use have declined in recent years despite relatively rapid economic growth. In all sectors but transport, substantial reductions have already occurred in the level of carbon emissions per unit of GDP output. At the same time, a number of official and unofficial studies have pointed out that the UK has one of the largest remaining potentials amongst comparable industrialized countries for achieving further CO₂ reductions through the implementation of cost-effective energy efficiency and fuel switching measures. This paper discusses past and present patterns of energy use and carbons emissions in the UK. The analysis then examines historical trends in UK energy policy and presents policy options for further reducing the UK's energy-use and carbon emissions in the future.     

部分种子成分的特征X射线在等效生物材料中衰减的测定

用Ｓｉ（Ｌｉ）探测器实现了Ｎａ、Ｍｇ、Ｓ、Ｃｌ的特征Ｘ射线在有机膜中的相对衰减以及与Ｏ、Ｋ元素的特征Ｘ射线能量相当的Ｘ射线或轫致辐射在有机膜中的相对衰减，分别得出了它们减的数学描述，并把实验得到不同能量的Ｘ射线在有机膜中的质量吸收系数与Ｂｅｒｋｅｌｅｙ的ＯＣＧ软件计算出的结果相比，相关都小于３０％。     

面流消能近底紊动流速特性的研究(面流消能试验研究之一)

本文主要论述了面流消能五种典型流态近底紊动流速特性,总结出了近底时均流速和紊动强度沿程变化规律,提出了近底紊动流速可能出现的最大瞬时值及相应位置的计算公式。面流消能工程的下游防冲设计中考虑的主要水力参数之一是,消能段近底流速紊动可能出现的最大瞬时值及其相应的部位,但目前国内外研究成果较少。笔者通过水工模型试验重点研究了面流消能各典型流态近底流速及其紊动纵向分量沿程的变化规律,并提出了计算公式,为优化面流设计提供科学依据。     

Thermodynamic Analysis of Various Dehumidifying Dryers for Wood

Typical methods of dehumidification of air circulating in the dehumidifying driers (indirect and direct cooler and partial exchange of the air) were analysed. Energy aspect of cooler operation was evaluated. The method for minimization of unit thermal energy consumption in a dehumidifying drier by the optimal selection of the cooler point was also given. Methods of the heat recovery of heat conveyed in a cooler lending to save energy (heat regeneration. expansion and compression of the air, a dehumidifier) were analysed. It was indicated that introduction of dehumidifiers into contemporary wood driers caused significant improvement of energy aspects of their operation     

Air Filtration and Radon Decay Product Mitigation

Air cleaning as a means of mitigating the risks arising from exposure to indoor radon progeny has been evaluated in a single-family house in the north eastem US. using an automated, semi-continuous activity-weighted size distribution measurement system. The measurements included radon concentration, condensation nuclei count, and activity-weighted size distribution of radon decay products. Measurements were made in the house with and without an operating air filtration system and with various particle sources common to normal indoor activities operating. Aerosols were generated by running water in a shower, candle burning, cigarette smoking, vacuuming, opening doors, and cooking. Using a room model, the changes in attachment rates, average attachment diameters, and deposition rates of the unattached fraction with and without the air cleaning system were calculated. In the presence of active aerosol sources, the air filtration unit typically reduced the concentration of particles within the hour following the end of particle generation. After candle burning, cigarette smoking, and vacuuming in the bedroom, the reductions of PAEC by air filtration are about 60% with the air filtration system operating in the bedroom. During cooking in the kitchen, the reductions of PAEC in the bedroom with the air filtration system were about 40%. However, for all cases the dose reductions were smaller than the particle and PAEC reductions. For those particles that were generated within the bedroom, there was a 20% to 50% reduction in dose. In the case of cooking where the door was open and particles infiltrated from the rest of the house, the dose reduction was only 5% on average and appears to be insignificant. Thus, the dose reductions were h e r than the reductions in activity concentration, but there were no cases where the estimated dose actually increased.     

Optimization of metal-based multilayers for transparent heat mirrors

Multilayer calculations by conventional matrix methods for dielectricum/noble metal/dielectricum systems on glass have been performed. The aim has been to maximize the integrated parameters for solar transmission, T_sol, and transmission of visible light, T_eye We have found that Ag is superior for maximizing the transmittance over the narrow visible wavelength range owing to the low internal absorptance. When solar energy transmission is considered multilayers based on Au are the best choice for metal film thicknesses above 15 nm. For thinner films, Ag is still to be preferred.