提高K-9曲拐质量的热处理工艺

K-9曲拐质量不合格主要是由于热处理后，珠光体数量太少所引起。因此应用正交试验，合理地选择了热处理工艺参数，提高了出炉温度，增加了珠光体数量，解决了K-9曲拐的质量问题。     

微波热液法制备光催化TiO2功能材料

采用微波加热法，研究了钛配离子热分解水解反应的规律。结果表明，水解产物在大气气氛和300℃下煅烧2h，所得产物为锐钛型TiO2粉末。在紫外线照射下，乙酸经Ti02光催化反应12h后，残余量小于初始量的20％。     

淀粉液化液灭酶方法的研究

某些情况下淀粉液化液需要严格控制液化的程度 ,因此需要及时终止残余淀粉酶的活性。实验用降低液化液 pH值、升高温度、以及两者并用等 3种方法结束液化反应过程 ,实验结果可作为工业生产过程参考。     

Forced convection subcooled boiling of binary mixtures

A mode based on an additive mechanism of heat transfer is proposed for forced convection subcooled boiling of binary mixtures. The contributing modes of heat transfer are: (i) the heat transferred as latent heat by the rising bubbles, (ii) the heat transferred as the heat contained in the superheated thermal layer that is removed from the surface in the wake of the rising bubbles and (iii) the single phase forced convection heat transfer from the heating surface not influenced by the bubbles. Experimental data from the literature on binary systems show good agreement with the model, validating the postulated mechanism.     

ZG3Cr13钢经长期时效后组织及硬度的研究

研究了ZG3Cr13钢在550℃～600℃的工作温度区间经2500h长期时效后的硬度及组织的变化。结果表明，在时效1000h内，硬度有明显的下降，之后趋于稳定；组织变化与正常处理后的组织均匀化程度有关，原始组织越均匀组织稳定性和热强性越高。     

催化燃烧炉的节能性分析

传统的火焰燃气炉往往会产生不同数量的氮氧化物(NO和NO2)、一氧化碳等不完全燃烧产物,造成了环境污染和能源浪费.催化燃烧作为一种新的燃烧方式,打破了传统火焰燃烧的可燃界限,实现了贫甲烷/空气混合物在可燃界限以下的燃烧,燃烧效率高,提高了能源利用率.将催化燃烧应用于燃气炉,可以解决燃气炉由于火焰燃烧带来的燃烧效率低等缺点,达到节约能源的目的.以催化燃烧和燃气炉为依据,在催化燃烧炉Ⅰ型的基础上研制出催化燃烧炉Ⅱ型,分析了催化燃烧炉的热损失以及热效率,并与传统火焰燃烧炉做了比较.结果表明,催化燃烧炉Ⅱ型的热损失并不大,热效率较高,且其污染物排放量极低.     

Optimization of metal-based multilayers for transparent heat mirrors

Multilayer calculations by conventional matrix methods for dielectricum/noble metal/dielectricum systems on glass have been performed. The aim has been to maximize the integrated parameters for solar transmission, T_sol, and transmission of visible light, T_eye We have found that Ag is superior for maximizing the transmittance over the narrow visible wavelength range owing to the low internal absorptance. When solar energy transmission is considered multilayers based on Au are the best choice for metal film thicknesses above 15 nm. For thinner films, Ag is still to be preferred.     

40Cr钢复合热处理强韧化

用光学及电子显微镜(SEM.TEM)观察不同热处理的40Cr 钢的冲击及断裂韧性断口、及金相组织,阐明其间相互关系;断口结构可反映断裂特征,组织情况;细化晶粒提高强度、塑性和冲击韧性,但却减少脆断的特性距离 l 因而降低 K_(1c)模;减少碳(杂质)偏聚而使其呈较均匀地分布,从而减少可诱发塑坑的较粗大的碳(杂质)化合物的析出,即增加塑坑的间距 di 以及增加塑断组成物。从而都可增加断裂临界应变 ef,都可以提高 K_(1c)40Cr 复合热处理既靠先超高温淬、回火以减少碳(杂质)偏聚,改善其分布,以反增加位错马氏体从而提高 K_(1c),也靠后淬、回火细化晶粒而提高强度、塑性和冲击韧性,各自发挥长处达到强韧化。     

重油纳米化助燃效果研究与表征

将复配的分散剂加入重油中制备得到重油纳米颗粒，采用氧弹热值对比法对所研制的纳米化重油进行实验室评价。研究结果表明，纳米化后的重油燃烧性能得到了改善，在掺水量为3％～12％时，重油的燃烧效率提高了2．5％～6．1％。通过TEM观察，纳米化后的重油呈水包油（O／W）型乳液结构，油水界面清晰，界面膜较厚，乳化油粒径约为20～50nm，油水分散均匀，并且分散后的重油粘度增幅小，掺水量在15％以内，粘度增幅不超过20％，并且随着掺水量的增加，乳化重油的粘度逐渐减少。另外，乳化重油稳定性好，室温下至少可保存6个月，在80℃下存放3天未发生破乳现象。     

Spectral Feature Analysis of Semiconductor Thin Disk Laser

The semiconductor thin disk laser is a new type of semiconductor laser. This work gives the basic operation function of the semiconductor disk laser, and analyses the heat effect by the experimentally measured photoluminescence spectrum of the laser chip at different pump power and different temperatures. We can see that: with increasing pump power, the thermal effect of the gain material becomes seriously and causes the saturation of carrier lifetime, so the electron-hole pair created in the absorbtion lay...