Influence of the Transport Properties of the Crystal/Heat Transfer Surface Interfacial on Fouling Behavior

One method to reduce fouling is to extend the induction time by a defined modification of the interfacial interactions between the heat transfer surface and the crystalline deposit. Since these interactions are a result of both molecular and mechanical forces, two approaches for fouling mitigation have been developed: (a) Modification of the energy related properties of the heat transfer surface and (b) Modification of the geometry related properties of the heat transfer surface.     

多孔挡板流化床还原UO3反应器模型的研究

针对ＵＯ＿３的Ｎ＿２还原反应建立了多孔挡板流化床反应器模型。将多孔挡板床的每一级视为具有相似的流动状态，每一级的上、下段称为稀、密相段，分别用鼓泡床和活塞流模型描述。该模型的计算值与￠６３ｍｍ的多孔挡板床Ｈ＿２还原ＵＯ＿３的热态实验值能较好的吻合。还预计了还原温度、操作气速和挡板结构参数对固相转化率的影响，为该类反应器的工业设计、放大和优化提供了依据。     

Non-steady-state model for kinetics of free radical polymerization, 4. Direct thermal initiation

This paper deals with the non-steady-state kinetics of direct thermal initiated polymerization. The initiation is assumed to be a bimolecular reaction of the monomer. The relationship between the radical concentration and the monomer conversion is rigorously derived. In further treatment a few very close approximations are introduced based on the fact that the number of monomer molecules reacting in the initiation step is much less than that consumed in the propagation step for a process producing high polymer, and the value of the rate constant for propagation or chain transfer is much lower than that for chain termination. Expressions for various molecular parameters, such as molecular weight distribution, number-average and weight-average degrees of polymerization, and dispersity, are given. Several numerical examples are provided.     

Significance of fluid regime in biological filtration

A dispersed flow model previously developed to study substrate utilization in unsaturated media was experimentally verified and its practical application was considered. For this purpose, measurements were made using tap water and a synthetic feed solution. The importance of the change in fluid regime as regards to the simultaneous transport and reaction within biological filters were demonstrated. The effect of drop formation and the breakage of liquid jets inside the filters on substrate utilization was also shown.     

Transient operation of a catalytic liquid-liquid plug flow reactor for kinetics measurements

A centrifugal partition chromatograph (CPC) was used as a liquid-liquid catalytic reactor for the isomerisation of hexen-3-ol into ethylpropylketone with a water soluble rhodium catalyst. Global mass transfer coefficients were measured and shown to depend on both the nature of the solute and the flow rate. Liquid-liquid partition isotherms were also determined with the CPC using elution chromatography. Finally, a reactor model was derived to account for the experimental results obtained both under stationary and transient (pulse) conditions. A parameter sensitivity evaluation is also presented.     

Geometric features of the flame propagation process for an SI engine having dual‐ignition system

Flame front surface area and enflamed volume (the volume enclosed with flame front) is theoretically analysed for a spark‐ignition engine, having cylindrical disc‐shaped combustion chamber with two spark plugs located axisymmetrically on cylinder head, between cylinder axis and cylinder wall. Spherical flame front assumption is used. A computer code is developed based on purely geometric consideration of the flame development process in combustion chamber, and is used to investigate the effects of variations of spark plugs' locations on geometric features of the flame front. A comparison has also been made with a spark‐ignition engine having one spark plug at the same location. Copyright © 2002 John Wiley & Sons, Ltd.     

面流消能近底紊动流速特性的研究(面流消能试验研究之一)

本文主要论述了面流消能五种典型流态近底紊动流速特性,总结出了近底时均流速和紊动强度沿程变化规律,提出了近底紊动流速可能出现的最大瞬时值及相应位置的计算公式。面流消能工程的下游防冲设计中考虑的主要水力参数之一是,消能段近底流速紊动可能出现的最大瞬时值及其相应的部位,但目前国内外研究成果较少。笔者通过水工模型试验重点研究了面流消能各典型流态近底流速及其紊动纵向分量沿程的变化规律,并提出了计算公式,为优化面流设计提供科学依据。     

Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.     

Thermodynamic Analysis of Various Dehumidifying Dryers for Wood

Typical methods of dehumidification of air circulating in the dehumidifying driers (indirect and direct cooler and partial exchange of the air) were analysed. Energy aspect of cooler operation was evaluated. The method for minimization of unit thermal energy consumption in a dehumidifying drier by the optimal selection of the cooler point was also given. Methods of the heat recovery of heat conveyed in a cooler lending to save energy (heat regeneration. expansion and compression of the air, a dehumidifier) were analysed. It was indicated that introduction of dehumidifiers into contemporary wood driers caused significant improvement of energy aspects of their operation