运用现代CFD方法设计高效率的汽轮机(续前期)

论述了运用现代计算流体动力学(ComputationalFluidDynamics,CFD)技术设计高效率汽轮机的方法,典型应用的实例有全三维叶片级流场、叶片汽封和排汽蜗壳计算。计算结果和实际是相符的。进一步对结构性单元和非结构单元程序的计算结果进行了比较,已证明,非结构单元CFD程序用于复杂形状的流场计算时,结果与实际相当一致,并具有独特的功能。     

高压水射流射孔井眼应力数值模拟研究

水力射孔技术是一种新型完井方式,利用深穿透水力射孔技术辅助定向压裂,可实现油层改造和油井增产。考虑套管水泥环的影响,采用有限元理论结合ANSYS软件计算了高压水射流水力射孔井眼周围的应力,重点分析了水力射孔参数对井周应力的影响规律,初步研究了直井水力压裂时水力射孔对裂缝起裂的影响。计算结果表明,沿最大水平地应力方向布孔时,孔眼根部的周向拉应力最大,裂缝将会在孔眼根部起裂;选择合理水力射孔参数可有效降低地层破裂压力。研究结果可为高压水射流水力射孔辅助定向压裂提供参数优选的依据。     

水力压裂净压力拟合分析解释技术研究与应用

基于三维裂缝延伸模拟模型的水力压裂净压力拟合分析解释技术,提出了净压力拟合分析解释的一般步骤及理论方法,研究了现场监测净压力的计算方法,并介绍了其在现场施工中的应用情况。该技术可以帮助认识地层参数和压裂参数,提高压裂施工成功率和有效率。     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

氧气顶吹转炉溅渣护炉试验研究

采用水力模型研究方法 ,针对马钢 2 0t转炉进行溅渣护炉冷态模拟试验 ,得出最佳工艺参数为 :枪位 1680mm ,氮气流量为 110 0 0m3/h ,大流渣量 ,渣粘度适中。此外 ,在满足炼钢生产的条件下 ,采用夹角为 13°的喷头溅渣效果好     

ETR Ⅱ-30调速器液压控制系统

ETRⅠ-30调速器是瑞士爱舍维斯工厂生产的具有PID调节规律的电液调速器。本文对其液压控制系统作了较详细的介绍,供有关人员参考。     

Operating experience from the ehecatl wind turbines

This paper presents a summary of the mechanical features and the medium term operating experience from three small horizontal axis wind energy conversion systems covering a range of 500 to 5000 Watt, intented for rural and isolated communities. These turbines have a new regulator which reduces gyroscopic loads, is easy to adjust and could be manufactured stronger and in smaller sizes than the conventional tail vanes. It is concluded that is feasible to build cheaps and reliable wind turbine generators with an acceptable efficiency employing common-use elements, but is needed a careful and optimized design.     

AHMED experiments on hygroscopic and inert aerosol behaviour in LWR containment conditions: experimental results

Hygroscopic NaOH, CsI, CsOH and inert Ag aerosol behaviour at different temperatures and relative humidities (RH) has been studied in a well instrumented and controlled vessel of 1.81 m³ total free volume. Homogeneous thermal-hydraulic conditions for aerosol measurement in the vessel were achieved. The aerosol number and mass concentration were measured continuously during the experiments using a Condensation Nucleus Counter and a Tapered Element Oscillating Microbalance. The particle size distribution and chemical composition in the test conditions were measured by Berner low pressure impactors. In the case of NaOH the half life of the aerosol mass concentration was more than four times longer at low RH (22%) as compared to high RH (96%). The half lives of the CsOH and CsI aerosols were only twice as long at low RH as compared to high RH. Thus at high RH (96–97%) the half lives of CsOH and CsI were twice as long as the half life for the NaOH aerosol. The faster decay of the NaOH aerosol is due to the smaller density decrease of NaOH during water condensation. CsOH particles grew rapidly to their equilibrium size at all humidities. The measured equilibrium size for CsOH aerosol agree well with the calculated particle size at different RHs. Experimental results were also compared with calculations obtained by severe accident computer codes. These calculated results will be presented in a later paper.     

水力喷砂割缝增产增注技术的作用原理及展望

本文对从俄罗斯引进的水力喷砂割缝技术的发展过程、工作原理及该技术在大庆油田的试验情况做了详细的阐述。并对它的改进及其将来的推广与发展前景做了展望。     

利用钨极氩弧焊技术修复1#汽轮机转子的实践

本文主要介绍了我厂利用钨极氩弧焊将1#发电机组汽轮机转子修复的工艺过程.