Methane oxidation over vanadium-modified Pd/Al2O3 catalysts

Three different vanadium-modified Pd/Al₂O₃ catalysts were prepared and tested as catalysts for the deep oxidation of methane. Vanadium was added to the palladium catalyst by incipient wetness of palladium catalyst in order to modify its properties and improve its thermal stability and thioresistance. The behaviour of vanadium-modified catalysts depends on the concentration of this compound, being 0.5 wt.% the optimum amount. However, when strong catalyst poisons are present in the gas (SO₂), these modified catalysts do not show a better performance than unmodified catalyst. Bimetallic catalysts were tested with and without further reduction, being observed that reduced bimetallic catalysts perform worse than the non-reduced ones.     

高抗挤厚壁套管的性能及应用效果评价

中原油田套管损坏的主要原因是现有套管强度不够,无法抵抗盐膏层段的巨大外挤力。开发了TP130TT型高抗挤厚壁套管,其强度能很好地抵抗盐膏层巨大外挤力。实验室试验表明,各项性能指标达到了设计要求,现场使用取得了很好的效果,解决了中原油田盐膏层段套管强度不足的难题。     

载体比表面积及孔径对Nb_2O_5/α-Al_2O_3催化剂酸性及反应性能的影响

采用浸渍法制备了Nb2O5/α-A l2O3催化剂(简称催化剂)并用于环氧乙烷水合制乙二醇的反应,通过控制α-A l2O3载体中致孔剂的含量来调变载体的孔径、孔分布及比表面积;采用吡啶吸附红外光谱、氨程序升温脱附法研究了载体的比表面积及孔径对催化剂酸性及反应性能的影响。实验结果表明,产物的选择性受扩散因素及催化剂酸性的影响,而催化剂的酸量、酸密度可以通过载体的孔径及比表面积的变化加以调控。比表面积较小及孔径较大的载体对催化剂催化环氧乙烷水合制乙二醇的反应较为有利。当载体的比表面积小于0.80m2/g、孔径为4.00~8.00μm时,在反应温度160℃、反应压力1.5M Pa、n(H2O)∶n(EO)=22、液态空速25h-1的条件下,环氧乙烷的转化率大于99.8%,乙二醇的选择性超过89.9%。     

宝浪油田宝北区块低渗透油藏层系优化研究

针对宝浪油田宝北区块低孔低渗油藏地质特征以及油层层数多、分布井段长、部分零散层动用难度大等问题 ,研究了宝北区有效厚度、油层层数、单井产能及单井控制地质储量等层系划分与组合的技术经济界限 ,并在此基础上进行了宝北区层系划分与组合优化论证 ,最终优选出宝北区开发层系     

CeO2对RuO2／γ-A12O3催化剂湿式氧化降解苯酚性能的影响

采用浸渍法制备了RuO2／γ-A12O3和RuO2／CeO2／γ-A12O3催化剂，并利用XRD、SEM和XPS对催化剂进行了表征，研究了Ce的加入对RuO2／γ-A12O3催化剂表面分散性和催化剂表面元素Ru，O和Ce化学态的影响，同时考察了RuO2／γ-A12O3和RuO2／CeO2／γ-A12O3催化剂湿式氧化降解苯酚的活性，并深入探讨了Ce对RuO2／γ-A12O3催化剂的助催化作用。结果表明：Ce掺杂改性后，使催化剂表面Ru的化学态降低、表面氧空位增加，并且活性组分Ru的分散性增加，从而使RuO2／CeO2／γ-A12O3催化剂的活性提高，因此Ce起到了显著的助催化作用。     

一种制氢预转化催化剂还原的新方法

对上海高桥分公司2×10~4m~3/h(标准状态)制氢装置原设计的预转化催化剂还原流程进行了改进。先跳开预转化反应器,利用转化炉制取氢气,再用自产的高纯氢气代替重整氢,对预转化催化剂进行单独升温还原,避免了催化剂在还原初期因发生甲烷化反应而超温失活的问题,使催化剂具有更好的活性和稳定性。     

凝胶成型法制备加氢催化剂载体的研究与工业化生产

采用凝胶成型法制备加氢催化剂载体，并进行了工业放大试验。通过BET、NH3-TPD、H2-TPR等表征手段及实际的加氢反应性能评价对凝胶成型法制备的载体及加氢催化剂与常规方法进行对比分析，结果表明，采用凝胶成型法所制得的载体及催化剂均具有较高的孔体积和比表面积、较低的堆密度，其机械强度可满足工业要求，总酸量及中强酸酸量得到提升，催化剂活性组分与载体强结合力得到削弱，金属利用率提高，应用性能明显优于传统方法制备的加氢催化剂载体。通过该方法完成了加氢催化剂载体的工业生产，所生产的载体应用于天津院THDS-3加氢精制催化剂取得了良好的工业应用效果。     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

Cd-ZSM-5沸石催化剂的制备、表征和芳构化催化性能

采用离子交换、浸渍和混合三种方法制备镉改性ZSM-5沸石催化剂,考察了改性方法和镉含量对催化剂的表面酸性和Cd状态以及芳构化性能的影响。结果表明,加入镉降低了B酸性,Cd~(2+)与沸石结合形成了L_(1612)酸中心,其生成量取决于改性方法和Cd含量,并与芳构化活性提高有直接关系。     

Sulfated zirconia catalysts: Are Brønsted acid sites the source of the activity?

The thermal decomposition products of pyridinium sulfate differ from those of pyridinium sulfate supported on zirconia which in turn differs from that of pyridine adsorbed on a sulfated zirconia. Unsupported pyridinium sulfate decomposes to produce pyridine and sulfuric acid, and these subsequently react to produce oxides of carbon and sulfur. Zirconia that is sulfated and then exposed to pyridine does not release detectable amount of pyridine during heating in an inert gas; rather the pyridine undergoes oxidation reduction reactions simultaneously to release CO₂ and sulfur compounds. Pyridinium sulfate supported on zirconia decomposes upon heating to release pyridine and sulfuric acid, which reacts with the zirconia. The desorption of pyridine in one case and only CO₂/SO_x in the other case suggests that sulfated zirconia does not contain Brønsted acidity that can form pyridinium sulfate.