The effect of additives on the thermal stability of poly(vinyl chloride)

The effect of a range of organic additives on the thermal stability of poly(vinyl chloride), both with and without a chloroparaffin extender, was studied using a number of experimental techniques. Of the additives used the best overall balance was provided by pentaerythritol, which increased stability when the extender was present and had no effect when it was absent. The congo red test emerged as the most suitable technique, being consistent and inexpensive and able to screen several additives simultaneously. Isothermal differential thermal analysis correlated with the congo red test but required more expensive equipment, was time-consuming and demanded good mixing of the poly(vinyl chloride) compound to give reproducible results. Thermogravimetry was not sufficiently sensitive and the heat stability test was the least useful of all.     

Thermal degradation of cinnamoylated poly(vinyl alcohol)

Thermogravimetry and pyrolysis in combination with gas chromatography and infrared spectroscopy were the experimental techniques applied to the thermal degradation of cinnamoylated poly(vinyl alcohol) samples, constituted from vinyl alcohol-vinyl cinnamate photocrosslinkable copolymers. The thermal decomposition products include gases, liquids and solids. The gases are formed from saturated and unsaturated volatile hydrocarbons C₁? C₄, carbon monoxide and carbon dioxide. The liquid fraction includes aromatic hydrocarbons and some oxygenated organic compounds. The solid product identified in the greatest amount was cinnamic acid. The content in the thermal decomposition products varies considerably both with copolymer composition and temperature.     

Open‐cycle OTEC systems with freshwater product: Effects of noncondensable gases on performance of condenser

An open‐cycle ocean thermal energy conversion (OC‐OTEC) system is one of the energy conversion methods used to generate electricity from ocean thermal energy. For the OC‐OTEC system, steam evaporated from the surface seawater due to flash evaporation drives the turbine. At that time, dissolved gas such as air is introduced into the low‐pressure system (OC‐OTEC system) as the noncondensable gas, which degrades the performance of condensation heat transfer. In this paper, a small‐scale OC‐OTEC experimental unit experimentally investigates the effect of noncondensable gas on the heat transfer performance in a condenser. The experimental results are discussed in comparison with theoretical estimation by the Sparrow–in method. It is shown that the condensation is occupied by heat and mass transfer near a condensation surface and that the condensation efficiency is affected by exhaust quantity of noncondensable gas at a relatively high concentration ratio of condensable gas. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 154(1): 29–35, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20179     

From hospital to municipal cogeneration systems: an Italian case study

A mixed integer linear programming model combined with a more traditional design by scenarios is proposed to optimize facilities size and operation mode of a municipal energy system involving significant civil centres and a hospital. Moving from the need of a new heat and power station for the local hospital due to the construction of new pavilions, the opportunity of involving other centres in the neighbourhood in a distributed cogeneration system is analysed, increasing system complexity step by step. Smaller cogeneration units tailored to hospital needs are rewarding ventures with relatively low risks but, in a country whose traditional power generation systems heavily rely on fossil fuels and where energy policy and market conditions can make it profitable to sell surplus power, district heating systems foster the installation of larger cogenerators and lead thereby to higher profits and to better performance as for primary energy savings and greenhouse gases emission reduction. Copyright © 2006 John Wiley & Sons, Ltd.     

A load dispatch method using fractional programming and semidefinite programming

This paper describes a load dispatch method which minimizes power cost—[fuel cost]/[electric output]—for a power system with thermal plants and energy storage facilities. The proposed method employs fractional programming to convert a minimization problem with fractional objective function to a series of quadratic minimization problems, and semidefinite programming to solve converted problems. The method provides the optimum time‐dependent power output/input and storage level of energy storage facilities as well as time‐dependent power output of thermal plants. The method has been applied to a power system with five thermal plants, two energy storage facilities of various performances, and five load demands. The optimum load scheme of four time mesh points is obtained for the thermal plants and energy storage facilities. The fractional programming successfully converges the optimal scheme through a few iterations. The semidefinite programming deals with a variable matrix of 164 dimensions, and 185 inequality constraints. © 2001 Scripta Technica, Electr Eng Jpn, 138(2): 49–58, 2002     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

沼气汽车加气站的探讨

分析了适合于汽车加气用沼气的品质，就沼气汽车加气站的流程、设备选型等进行了论述。     

Effect of water inlet velocity on thermal stratification in a mantled hot water storage tank

Thermal stratification in a mantled hot water storage tank is analysed numerically for different water inlet velocities. The aim is to obtain higher thermal stratification and supply hot water for usage as long as possible. Twelve different water inlet velocities to the hot water storage tank are considered. The numerical method is validated by comparing its results against experimental and numerical results from the literature. It turned out that the results obtained from the numerical analysis have shown very good agreements with the results from previous works. As a result, the water temperature in the tank increases with the increase of the water inlet velocities to the mantle but this increment is not proportional. After a period of operation of 7.2 h, which corresponds to the average sunshine duration in Turkey, temperature increments of 6.5 and 35 K have been estimated for the hot water inlet velocities of 0.01 and 0.3 m s^?1, respectively, at a radial distance of 0.1 m and a height of 1 m inside the storage tank. Copyright © 2005 John Wiley & Sons, Ltd.     

Effect of pretreatments and freezing rate on the firmness of potato tissue after a freeze–thaw cycle

The texture of potato tissue after a freeze–thaw process using different freezing rates and different pretreatments was analysed, in order to select the best strategy for optimum preservation of the textural characteristics of pre‐frozen potato. Ten blanching conditions were tested and a two‐step blanching process with calcium chloride (0.07 g mL^?1) proved the most effective in protecting the tissue after a freeze–thaw process (maximum load force around 10–55% of the raw tissue, depending on potato batch, for air‐blast freezing and 20–60% for immersion freezing). Vacuum impregnation at 100 and 400 mbar, even when followed by different pre‐drying treatments to remove excess water, was very detrimental to resistance to a freeze–thaw process (maximum load force below 10% of the raw tissue for air‐blast freezing and below 20% for immersion freezing). Microstructure analysis confirmed better tissue integrity retention with ethyleneglycol immersion freezing instead of air‐freezing. Differences were found between batches with a 6‐month difference in storage time, indicating that the fresher batch was more suitable for freezing.