Ce对过共晶Al—Si合金熔体粘滞性和结构的影响

研究了Ce对Al—16％Si合金熔体粘滞性的影响。结果表明：Ce的加入增加了合金熔体的粘度，且随着Ce含量的增加粘度值也增加。结合加入Ce的Al—16％Si合金氢含量的变化、凝固组织和DSC曲线研究了熔体结构的变化，分析了粘度与液态结构变化之间的关系。     

液膜法分离富集,测定水中微量锶

用乳状液膜体系对锶进行分离富集，该体系包括协同流动载体（ＰＭＢＰ，ＴＢＰ），表面活性剂（ＳＰＡＮ８０）增强剂（丙三醇）溶剂（正己烷）和内相（１．２ｍｏｌ／Ｌ的盐酸溶液），实验表明，在适宜的条件下，锶的富集效率可达９９．５％以上，而在此条件下许多共存离子，如Ｆｅ＾３＋，Ａｌ＾３＋，Ｃａ＾２＋，Ｍｇ＾２＋，Ｂａ＾２＋，Ｃｒ＾３＋，ＣＯ＾２＋，Ｎｉ＾２＋，Ｚｒ＾４＋，Ｃｕ＾２＋，Ｚｎ＾２＋，Ｐｂ＾２＋和     

Borides at interfacial zone of IC6 TLP bonded joints

1　INTRODUCTIONTransientliquidphase (TLP)bondingtechniquehasbeensuccessfullyusedinjoiningheatresistantal loys ,likeHastelloyX ,Inconel713C ,In10 0 ,Udimet5 0 0 ,70 0 ,MarM 2 0 0 ,0 0 7,2 4 7,30 2 ,Rene′80 ,TD NiCr ,MA75 4,6 0 0 0 ,PWA14 2 2 ,CSMX 2etc ,whicharesusceptibletohotcrackingor post weldheat treatmentcrackingproblemsduringfusionweld ing[14 ] .Inaddition ,therewerereportsofjoiningNiAlandTiAlintermetallicsbyTLPbondingmethod[510 ] .Forexample ,Galehadinvestigatedthemic…     

铝液充型过程计算机可视化技术研究

采用透明的耐高温石英玻璃观察窗,观察和记录铝液充型过程的图像信息,分析铝液的充型过程;以图像处理技术和计算机技术为基础,通过充型过程铝液自由表面的边缘检测及提取技术,获取液体充型的自由表面曲线,定量分析铝液充型过程的自由表面变化;定量分析的试验结果表明,铝液实际充型过程自由表面的变化对浇注系统设计的合理性具有一定的指导意义.     

Heat capacity of liquid and undercooled liquid metals and alloys

Trends in the dependences on temperature and concentration of experimentally determined heat capacities of liquid and undercooled liquid metals and alloys are discussed. A new adiabatic calorimeter for determining the heat capacity of liquid alloys up to 1500 K is described. The ability of several approximations and models to describe the different characteristics of the heat capacity of liquid and supercooled liquid metals and alloys is demonstrated.     

Grinding-hardening with liquid nitrogen: Mechanisms and technology

This paper studies an innovative development of a steel grinding–hardening technology using an inert cryogen—liquid nitrogen. It was found that phase transformations took place during grinding with the application of liquid nitrogen and resulted in hardened surface layer in a ground component. The layer had a fine laths martensite structure which gave rise to a remarkably high hardness. It was also shown that the treatment can produce superior surface integrity, with compressive surface residual stresses and without surface oxidation. Due to the inert nature of the liquid nitrogen, the grinding process becomes environmentally conscious.     

液锻连挤硅线石粒子/铝复合材料的摩擦磨损行为

采用液锻连挤成形工艺获得了一种新型硅线石颗粒增强LY12铝基复合材料,其性能可与常规热挤压件媲美.摩擦磨损性能测试表明:硅线石颗粒增强铝基复合材料具有优良的摩擦磨损性能,且其耐磨性能随粒子体积分数增加而增加.材料经液锻连挤后,硅线石粒子在强大三向压应力作用下嵌镶于基体内,粒子很难拉脱,承受摩擦力的作用时,硅线石粒子起支承作用,粒子硬度高,故使复合材料整体耐磨性能提高.     

黑液中的多糖对合成本素胺乳化剂的影响

直接以浓缩黑液为原料，通过环氧氯丙烷引入季铵基团制取阳离子型木素胺乳化剂。对产品和原料黑液做了剖析，证明黑液中的非本素有机物发生了胺化反应．应用试验证明这部分胺化产物具有助乳化和稳定乳液的作用。     

An improved light attenuation technique for measuring large interfacial areas

A laser-based light attenuation technique was successfully used to measure interfacial areas as high as 5832 m²/m³ and Sauter mean bubble diameter varying between 50 and 5600 μm. Good agreement between this approach and the photographic technique was obtained particularly at low gas holdups.     

CO气氛中液相催化COS水解活性的研究

在鼓泡反应器中，采用液相催化剂，对高浓度CO气氛中高浓度COS的水解反应进行考察，研究催化剂浓度、气液体积比、温度的变化对COS水解转化率及催化体系稳定性的影响，得出最佳工艺条件，并对反应机理进行初步探讨。结果表明,COS水解转化率随气液体积比增大而降低，随催化剂浓度增大而升高；在常温、常压和气液体积比为150 h^－1的条件下，质量分数为10%的催化剂水溶液中COS的水解转化率可达100%，连续使用20 h转化率不变。