Grain Boundary Sliding in Fatigue of Pure Aluminum

The distributions of plastic strain near grain boundaries induced by fatigue loading were investigatedby the fiducial grid method in pure aluminum specimens, and the resulted grain boundary sliding(GBS) was systematically analysed. The results show that the strain field near a grain boundary isnonuniform. GBS is restricted by the junction of grain boundaries and causes discontinuities of bothdisplacement and strain. A peak value of shear strain was created in short-range area across the grainboundary. GBS plays an important role in cyclic softening and secondary hardening. The control fac-tor of GBS is the relative orientation between two grains and the macro orientation of the grainboundary rather than the ∑ value of the boundary.     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

纳米级BaAl_2O_4微粉的制备和性质

分别用溶胶 -凝胶法、低温固相反应法 ,制得了纳米级BaAl2 O4微粉 ,用电镜观察了其形貌和粒径的大小 ,用X-射线衍射仪进行了物相分析 ,测定了其纯度与晶型 ,讨论了制备方法与粒度大小的相互影响     

重载齿轮齿面疲劳损坏及预防

点蚀和剥落是重载齿轮齿面疲劳损坏最普遍的形式.根据齿轮失效分析实例,对齿面初始点蚀、破坏性点蚀和齿面剥落等三种主要疲劳损坏的特征、发生部位及破损危害程度进行了分析研究,较系统地论述了齿轮接触疲劳破坏机理,影响因素及其产生原因,并对有关的齿面破坏提出了相应的预防措施.     

大庆长垣外围油田的开发问题

本文在对大庆长垣外围油田的地质情况、油藏类型综合分析评价的基础上,论述了开发这些油田的一系列有关问题。     

Measurement of Thermal Diffusivity at Low Temperatures Using an Optical Reflectivity Technique

An experimental arrangement has been developed for measuring the transient temperature responses and the thermal diffusivities of foil materials in the range of 10 to 300K by using the optical reflectivity technique. The cryogenic system with optical windows is designed to provide temperatures from 10 to 300 K. The front surface of a foil specimen is heated by a pulsed Nd:YAG laser. In situ measurement of the reflectivity of a continuous-wave He–Ne laser at the rear surface is conducted on the microsecond time scale. Using the temperature dependence of reflectivity, the transient temperature response is deduced. The thermal diffusivity is obtained by fitting Parker's formulae to the experimental data on temperature rise. Stainless-steel foils are chosen as samples and are studied in the region from 10 to 300 K. The accuracy is examined by comparing the present results with the theoretical temperature responses and thermal diffusivity data from the literature. Good agreement is observed.     

测定钠中杂质的手动阻塞计的研究

文章介绍了测定钠中杂质浓度的手动阻塞计的原理、装置和实验结果。为了减少测量误差,我们研究了影响准确测定阻塞温度的因素,并且找到了减少测量误差的办法。在同样的杂质饱和温度下,该阻塞计测得的高、低阻塞温度所对应的杂质浓度差是很接近的。对氧其差值为1.03ppm;对氢为0.0763ppm。     

X60管线钢疲劳特性的研究

利用2、4和14mm的X60钢紧凑拉伸试样进行同样应力水平、固定应力比（R＝0．1）的疲劳裂纹扩展试验，揭示出高韧性管道钢的疲劳裂纹扩展存在显著的厚度效应。由于应力水平低，相应的离面应力也低，不足以导致分层开裂，因此，裂纹端部的三维应力约束随厚度增加而增大。4mm试样的疲劳裂纹速率远高于2mm试样，但厚度再增大，裂纹扩展速率不再有显著变化。进一步对表面裂纹试样进行疲劳裂纹扩展试验，并用勾线法纪录裂纹扩展情况，利用穿透裂纹的da/dN-ΔK曲线预测表面裂纹扩展，用2mm厚试样的数据控制裂纹表面长度的扩展，用14mm厚试样的数据控制裂纹底部沿厚度方面的扩展，得到了与表面裂纹扩展实验吻合很好的预测结果。     

含氯取代基的聚间苯二甲酰间苯二胺的合成与表征

以 2 ,5 -二氯对苯二甲酰氯作为第三单体 ,将其与间苯二甲酰氯、间苯二胺在N ,N -二甲基乙酰胺中进行低温溶液共缩聚反应 ,合成了含氯取代基的聚间苯二甲酰间苯二胺。研究了单体摩尔浓度、反应初始温度、叔胺添加剂种类、第三单体用量等对共聚物相对分子质量的影响 ,并用红外光谱、热重分析等方法对共聚物进行了表征。     

低品位硼矿的富集加工技术

报道了青海大柴旦地区低品位硼矿富集加工的新工艺，该工艺使硼矿品位30％－35％，B2O3收率大于80％，该工艺路线已工业化。