海上无人驻守平台上的密闭循环涡轮发电机组

海上无人驻守简易平台设计是降低原油成本的重要手段之一,密闭循环涡轮发电机组(Closed Cycle Vapor Turbogenerator)是海上无人驻守平台上应用最可靠且低维护的远程发电系统。介绍CCVT这种发电机组,并讨论了在海上工程设计中需要考虑的问题,为今后简易平台上电站的选择设计提供参考。     

提高连续油管使用寿命的方法

从采用软件跟踪疲劳寿命 ,截断法 ,变径连续油管 ,反转使用连续油管 ,防止连续油管损伤 ,合理配置设备 6个方面讨论了控制管串疲劳 ,提高连续油管使用寿命的方法 ,并得出结论 :控制管串疲劳的方法中 ,最有效的方法是实际作业截断法。指出要尽量减少连续油管在带内压下工作 ,也要研究开发降阻性能好的工作液 ,以延长连续油管使用寿命、降低作业风险。     

HSLA-80/100钢的焊接

对ＨＳＬＡ－８０／１００钢的焊接性、焊接材料及焊接工艺进行了综述，并指出了现存在的主要问题。     

Open‐cycle OTEC systems with freshwater product: Effects of noncondensable gases on performance of condenser

An open‐cycle ocean thermal energy conversion (OC‐OTEC) system is one of the energy conversion methods used to generate electricity from ocean thermal energy. For the OC‐OTEC system, steam evaporated from the surface seawater due to flash evaporation drives the turbine. At that time, dissolved gas such as air is introduced into the low‐pressure system (OC‐OTEC system) as the noncondensable gas, which degrades the performance of condensation heat transfer. In this paper, a small‐scale OC‐OTEC experimental unit experimentally investigates the effect of noncondensable gas on the heat transfer performance in a condenser. The experimental results are discussed in comparison with theoretical estimation by the Sparrow–in method. It is shown that the condensation is occupied by heat and mass transfer near a condensation surface and that the condensation efficiency is affected by exhaust quantity of noncondensable gas at a relatively high concentration ratio of condensable gas. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 154(1): 29–35, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20179     

测井资料高分辨率层序地层分析

高分辨率层序地层学克服了岩性地层对比穿时的缺点.高分辨率层序地层对比是等时的高精度的地层对比,它满足了勘探开发中地层对比等时性和高分辨率的要求.测井资料的纵向分辨率较高,是高分辨率层序地层研究的重要资料.提出了利用测井相分析技术,从测井资料上识别出单井岩性和沉积微相剖面,结合测井曲线特征,划分单井基准面旋回,并进行连井地层等时对比,这为定量地进行高分辨率层序地层分析提供了一种方法.通过研究区实际资料的处理,验证了该方法的有效性.     

Crack growth in aluminium alloy sheet material under flight-simulation loading

Crack propagation tests were carried out on 2024-T3 sheet specimens to study the effects of omitting low-amplitude cycles from the gust-dominated TWIST load sequence (MiniTWIST) and the removal of small load ranges from the manoeuvre-dominated FALSTAFF load sequence (short FALSTAFF). In other tests high-amplitude loads of TWIST and MiniTWIST were truncated at different levels. The results are compared with data from similar test programmes, including crack initiation. Attention is paid to unstationary crack growth retardation and a transient retardation during initial crack growth started by an artificial crack.     

用于频率合成器的低损耗声表面波滤波器

简述了产生声表面波滤波器插入损耗的主要机理和获得低损耗的原则；介绍了根据此原则对１００～５００ＭＨｚ５种滤波器的研制过程和结果。实验表明，采用镜像阻抗连接换能器结构可达到３～４ｄＢ的低损耗，并成功地应用于频率合成器中。     

微波BJT超宽带低噪声放大器的设计

本文给出了一种频带覆盖达１０－１６００ＭＨｚ的微波ＢＪＴ超宽带低噪声放大器的设计方法，从微波ＢＪＴ的噪声模型出发，通过拟合５０Ω源阻抗下微波ＢＪＴ的噪声系数ＮＦ５０和Ｓ参数来提取其噪声参数，然后根据增益，噪声及驻波比要求优化设计放大器，使放大器在超宽带范围内获得平坦增益和低噪声，本文所给出的微波ＢＪＴ惨数提取及放大器优化设计方法已由实验结果所验证。     

Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.