Impact performances of steel tube-confined recycled aggregate concrete (STCRAC) after exposure to elevated temperatures

The impact behaviours of steel tube-confined recycled aggregate concrete (STCRAC) following exposure to elevated temperatures of 20 °C, 200 °C, 500 °C and 700 °C were experimentally investigated using a 100 mm-diameter split Hopkinson pressure bar (SHPB). The recycled coarse aggregate (RCA) replacement ratios were set as 0, 50% and 100%. The effect of RCA replacement ratio and exposure temperature on the impact properties of STCRAC were analysed in terms of failure modes, stress-strain time history curve and dynamic increase factor (DIF). The results show that the fire-damaged STCRAC can maintain its integrity during impact load. However, there were evident degradations in the dynamic behaviour of STCRAC after exposure to high temperatures of 500 °C and 700 °C. The ultimate impact strength, impact secant modulus and residual impact strength of STCRAC obviously decreased because of the damage due to high temperature exposure. But the degradations of both the ultimate impact strength and impact secant modulus of STCRAC under impact loading were less severe than those under quasi-static loading. The remaining strength factor and the DIF tended to increase with the raise of the elevated temperatures. Overall, during the impact loading, the fire-deteriorated STCRAC exhibited excellent impact behaviour.     

A first-principles investigation on mechanical and metallic properties of titanium carbides under pressure

The titanium carbides are potential candidates to achieve both high hardness and refractory property. We carried out a structural search for titanium carbides at three pressures of 0 GPa, 30 GPa and 50 GPa. A phase diagram of the Ti-C system at 0 K was obtained by elucidating formation enthalpies as a function of compositions, and their mechanical and metallic properties of titanium carbides were investigated systematically. We also discussed the relation of titanium concentration to the both mechanical and metallic properties of titanium carbides. It has been found that the average valence electron density and tractility improved at higher concentrations of titanium, while the degree of covalent bonding directionality decreased. To this effect, the hardness of titanium carbide decreases as the content of titanium increases. Our results indicated that the titanium content significantly affected the metallic properties of the Ti-C system.     

A direct two-dimensional pressure formulation in molecular dynamics

Two-dimensional (2D) pressure field estimation in molecular dynamics (MD) simulations has been done using three-dimensional (3D) pressure field calculations followed by averaging, which is computationally expensive due to 3D convolutions. In this work, we develop a direct 2D pressure field estimation method which is much faster than 3D methods without losing accuracy. The method is validated with MD simulations on two systems: a liquid film and a cylindrical drop of argon suspended in surrounding vapor.     

Reformate-enriched gasoline-ethanol blends: Volatility criteria and azeotrope formation

Four hydrocarbon-base gasolines (BG) were formulated from the local refinery streams; isomerate, reformate, and light naphtha. The formulations were enriched in reformate. Each of these BG formulations was blended with 10 vol% of anhydrous ethanol. From ASTM-D86 distillation data, eight distillation curves were constructed and the trend line equations of these distillation curves were developed. Also, the area under each distillation curve (AUDC) was calculated through calculus definite integration technique. Subsequently, the area due to azeotrope formation (ADAF) for each BG-ethanol blend was estimated. In this paper, the influence of increasing reformate proportions on the created positive azeotrope, was studied. Also the influence of increasing reformate proportions on vapor pressure, Temperature for the vapor-liquid ratio of 20, T50 and octane number was studied. The results show that the R² values of the distillation curve equations prove the reliability of the fits. Also, increasing reformate proportion in the fuel blend improves the octane number while increasing reformate proportion decreases the volatility of the fuel formulation.     

Tuning of Active Disturbance Rejection Control with application to power plant furnace regulation

Active Disturbance Rejection Control (ADRC) is emerging as a promising solution in dealing with the unmeasurable disturbances and unknown uncertainties, which are treated in a lumped manner and augmented as an extended state variable. Subsequently, an extended state observer (ESO) is designed to estimate and cancel the combined uncertain term in real time, modifying the uncertain plant to behave like a nominal model consisting of integrators. In the original ADRC formulation, the plant model is assumed to be of delay-free and its order is assumed to be equal to that of the real plant. However, a low-order ADRC is preferred and received a wide acceptance in practice because of its simplicity. Currently, the feasibility of such practice is not clearly revealed as well as its potential dangers. To this end, this paper analyzes the control mechanism from the perspective of the modified plant, which, in turn, would give guidance to parameter tuning. The effect of each parameter on the compensation efficiency and stability conditions of the modified plant is analyzed, based on which a complete tuning procedure for ADRC is developed where the initial settings is derived from the existing PI controller parameters. Finally, the proposed tuning method is experimentally used for a furnace pressure regulation of a 1000MW power plant, validating the feasibility of the low-order ADRC, even in the absence of both dynamic model and the information on the model order.     

高性能MIM材料烧结炉的特征及设备主要组成

根据国际和国内MIM材料烧结工艺最新的要求和技术特点,对改进MIM材料烧结炉的结构和排胶方法进行了分析和比较,并对比了MIM烧结使用的真空式批次炉和气氛式连续炉设备性能优缺点,提出了满足市场化要求的技术方案。     

Geotextile encased columns (GEC) used as pressure-relief system. Instrumented bridge abutment case study on soft soil

Geosynthetic Encased Sand Columns (GEC) have been frequently adopted in geo-engineering practice to improve bearing capacity, reduce settlements and accelerate consolidation in saturated soft cohesive ground (e.g. Alexiew et al, 2005; Alexiew et al., 2012; Raithel et al, 2005). The present paper extends these early views by introducing the use of columns to reduce the magnitude of horizontal earth pressures acting on structures adjacent to compaction fills. The monitoring program of a full-scale bridge abutment on soft soil supported by GECs and geogrid reinforced system is described, where field performance is monitored with pressure cells, electrical piezometers, inclinometers and settlement plates. Analytical and numerical analyses have been performed to help on interpreting experimental measurements. The collected database is interpreted to demonstrate that GEC can reduce by up to 50% the horizontal earth pressure over bridge border foundation piles when compared to values predicted for unreinforced ground and demonstrate that the work conformed to acceptable limits of behavior.     

Kinetics of development of physical contact in diffusion welding of titanium

Results of experimental investigations, carried out on specimens of OT4 and VT14 titanium alloys with microprojections simulating the roughness of actual surfaces, are used to determine the effect of the height of microprojections on the kinetics of development of physical contact in diffusion bonding. It is shown that with increase of the height of the microprojections, the rate of development of physical contact decreases. This is associated with the strain hardening of the metal in the contact zone determined by the localization of stresses and strains at the tips of the microprojections.     

Pressure welding of branch pipes with local heating

The process of pressure welding branch pipes with hot local heating and the ratio for calculating the conditions are proposed. The constitutive equations of the material in plasticity and creep are used. The energy method is used for calculating the pressure for the fracture axisymmetric field of the displacement speeds. The experimental and production results are presented.