Dual segment rectangular dielectric resonator antenna with metamaterial for improvement of bandwidth and gain

The simulation and experimental studies of an aperture‐coupled wideband dual segment rectangular dielectric resonator antenna with metamaterial for C‐band applications are presented in this paper. The antenna consists of Alumina (Al₂O₃) ceramic as upper segment and Teflon as lower segment. The combination of circular‐shaped coplanar split‐ring resonator and conducting strip has been used as metamaterial superstrate. With the use of metamaterial superstrate, the bandwidth of the antenna is increased by 48% through simulation and 22% experimentally. The broadside radiation pattern of the antenna is converted into directive radiation pattern with reduced beamwidth when metamaterial superstrate is used. The peak gain of the antenna is also enhanced by 33% through simulation and 31% experimentally with the use of metamaterial superstrate. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:646–655, 2014.     

带长矩形接管受压圆简体的有限元分析与强度计算

本文运用有限元软件FEPG,建立了带长矩形接管受压圆筒体的三维参数化有限元模型,研究了矩形接管部位的应力分布特点,按照分析设计规范对带长矩形接管受压圆筒体进行了强度评定,并针对应力分布的不合理性提出了结构改进措施。     

矩形截面深梁的一个新理论及其应用

综合考虑梁截面转动、相邻截面剪切变形和横向压力等影响推导出弯曲矩形截面深梁的新理论。作为算例,应用虚拟功的互等法具体求解了在均布载荷作用下两端简支深梁的弯曲问题,给出了这种情况的数值计算结果,与ANSYS有限元结果进行了对照,验证了该新理论的正确性。     

电路板雕刻机的运动控制系统设计

介绍了电路板雕刻机的运动控制系统的特点和规律,系统以3关节直角坐标型机器人为外部结构,基于Visval C＋＋的操做环境,控制核心采用DSP,同时与上位PC机通讯进行控制．对电路板雕刻机中的步进电机实现电气控制,以完成电路板的雕刻过程．     

水平矩形管内气液两相流界面波特性

<正>气液两相流中界面波的存在对传热、传质、阻力特性及稳定性都有很大影响。前人有关界面波的研究大多偏重于两相流中界面波的类型及其转变,而对其特征参数变化规律(如振幅、波长、频率和速度等)的研究则很少。但界面波对气液两相流流动阻力和流动结构影响机理的深入研究必须以了解界面波的各特性参数为前提,同时界面波有关特性参数的深入研究也可为气液两相流的数学理论化提供实验基础。 本文以气、水为工质,系统研究了水平矩形管内气液两相流的界面波特性。根据界面波在时域、幅域内的不同特征区别出了各种类型的波并给出了相应的波形和流型图。着重研究了界面波各特征量随气液两相流量变化的变化规律。     

矩形断面明渠中恒定均匀流的机械能损失

明渠流中机械能损失的确定是水力学乃至工程流体力学中的重要内容.以构建的明渠恒定流新的总流能量方程及矩形断面明渠三维层流运动的理论解为基础,通过理论分析与三维数值计算,就矩形断面明渠中恒定均匀流的机械能损失系数随雷诺数及宽深比的变化进行了深化研究,得到如下成果:1)在层流条件下,机械能损失系数一般均与雷诺数和宽深比有关,只有对宽深比大于6.5的宽浅明渠,其相应流动的机械能损失系数才仅与雷诺数有关,且在雷诺数相同的条件下,一般矩形断面明渠流的机械能损失系数要大于宽浅明渠流的机械能损失系数;2)在紊流条件下,机械能损失系数也一般均随雷诺数与宽深比而变,但对给定的宽深比,存在相应的特征雷诺数,当流动的实际雷诺数大于该特征雷诺数后,机械能损失系数则不再随宽深比而变化,且在宽深比一定的条件下,雷诺数越小,其机械能损失系数的修正值越大.     

纯铜薄板矩形盒拉深中法兰曲边的变形分析

作为矩形盒拉深试验研究的一部分 ,分析了成形过程中光刻网格变形的测量结果 ,指出法兰曲边变形中 ,角对称线上凹模口附近的径向拉变形随矩形盒角半径rc 增大而增大 ,但周向压变形几乎与rc 无关。并且在角对称线上存在径向压变形的区域 ,有助于减低曲边材料的流入抵抗     

坯料外形对镁合金矩形盒拉深成形的影响

用商业有限元软件模拟了在同一套模具和成形条件下不同毛坯外形的镁合金矩形盒拉深成形过程．依据数值模拟结果，分析了不同坯料外形对镁合金矩形盒拉深成形的影响。结果表明：使用矩形圆角坯料比其他坯料的成形性能好。     

Numerical simulation of small section rectangular tube in parallel welding

The welding temperature field and deformation of parallel arrangement small-section rectangular tubes is calculated by using a non-contact model. After comparing the computed results with the experimentally measured results, it shows that there exist big errors when applying this model to the numerical simulation of small-section rectangular tube＇ s welding temperature field and deformation. Based on a simple analysis of the errors, a contact model is presented. The heat transfer and stress analysis between small-section rectangular tubes and clamping fixture are simulated by using direct constraints method, and then the laws of the temperature distribution, which coincide with experiment, are obtained. A further numerical analysis of the stress and deformation are made, it shows that a ＂T＂ shaped stress-field is formed in the vicinity of the weld. As the stress-field departs from the centroid of tubes＇, this leads to the small rectangular tubes not only have a longitudinal deflection, but also have a transverse bending and deformation.     

薄壁方管激光弯曲过程的模拟研究

薄壁方管激光弯曲是一种利用激光加热来实现构件的柔性成形技术。研究了薄壁方管激光弯曲有限元模拟中的型处理、单元技术、边界条件、动热源构建、材料热吸收系数的选择、边界条件与初始条件等关键技术的处理，实现了薄壁方管激光弯曲过程的有限元模拟，分析了其变形机理。