环境温度对风压传感器精确度的影响探讨

对风压传感器的硅橡胶膜片弹性形变进行了理论分析,推测风压传感器的精确度可能受到温度的影响。通过工业压力校准器对传感器进行了压力校验。结果表明,风压传感器的精确度受温度与气压差的影响。该研究结果可用于指导风压传感器进行温度与气压差补偿设计。     

流水线上机械手克隆转换开关改性塑料的选择

转换开关是用在工业生产自动流水线机械手中一种易磨损和大量消耗的塑料制品,以前依靠外国进口,花费了大量外汇。由于转换开关的精度极高,甚至超过金属件的制造精度。故不仅要求制品在成型加工过程中不能有微小的变形,甚至需要严格控制塑料的收缩量。使得所有成型孔的精度达到IT6级以上,平面度不大于0.02 mm,圆柱度不大于0.01 mm。通过对亚光微珠增强聚碳酸脂改性材料的选择,实现控制了制品变形量和提高了耐磨性的目的,通过超高精度孔的二次限制工艺的实施,使得制品孔的精度可达到IT4级以上,圆柱度为0.002 mm以内。国产转换开关完全取代了进口产品,且其精度和寿命远高于进口产品,为超高精度注射件加工创出了一种新方法,也为有关单位节约了大量外汇。     

A Web Server for Designing Molecular Switches Composed of Two Interacting RNAs

The programmability of RNA–RNA interactions through intermolecular base-pairing has been successfully exploited to design a variety of RNA devices that artificially regulate gene expression. An in silico design for interacting structured RNA sequences that satisfies multiple design criteria becomes a complex multi-objective problem. Although multi-objective optimization is a powerful technique that explores a vast solution space without empirical weights between design objectives, to date, no web service for multi-objective design of RNA switches that utilizes RNA–RNA interaction has been proposed. We developed a web server, which is based on a multi-objective design algorithm called MODENA, to design two interacting RNAs that form a complex in silico. By predicting the secondary structures with RactIP during the design process, we can design RNAs that form a joint secondary structure with an external pseudoknot. The energy barrier upon the complex formation is modeled by an interaction seed that is optimized in the design algorithm. We benchmarked the RNA switch design approaches (MODENA+RactIP and MODENA+RNAcofold) for the target structures based on natural RNA-RNA interactions. As a result, MODENA+RactIP showed high design performance for the benchmark datasets.     

CYCLIC DEFORMATION OF COARSE GRAINED POLYCRYSTALLINE PURE Al——Ⅱ.FRACTURE SURFACE MORPHOLOGY

SEM photos for very coarse grained and high ductile polycrystalline pure Al show followingcharacteristics:A few fracture sources are concentrated,the crack propagates in fan-shapenear them,and the fatigue striations are cyclic cleavage facets.Each striation consists of awide cleavage facet and a narrow cleavage stage.Those stages often blunt due to plasticdeformation.The fatigue striations are clear and continual,and distribute over whole zone ofstage Ⅱ crack propagation.Two kinds of fatigue striations form in different levels,areconjoined by a“twisted baked piece of pastry”band.The secondary crack along the fatiguestriations was observed frequently.Some of them have already developed into secondarymacrocracks and secondary fatigue striations were found clearly on secondary fracture sur-face.The fracture surface can be divided into two parts,initiation and propagation zone of thecrack,however,no statical-fracture zone was observed.The mechanism to form striationswas preliminarily discussed.     

基于模型预测控制算法的多风储直流微电网分布式电压二次控制策略

针对含多组风储单元的直流微电网中蓄电池的电压优化控制问题,提出了一种基于模型预测控制算法的分布式电压二次控制策略.设计了一种多步长预测一致性模型作为电压预测模型,通过目标函数最小化求解预测系数,得到最优电压二次控制补偿量加入一次控制中,将传统一致性算法中比例积分控制器下的偏差调节问题转化为模型预测控制器下的电压跟踪问题进行求解,从而实现对直流母线电压动态响应的滚动优化.该方法有效解决了传统一致性算法下电压控制策略瞬态特性差和部分工况下存在控制误差等问题,并通过MATLAB/Simulink仿真平台搭建模型验证了不同工况下所提策略的有效性和优越性.     

马钢直弧型板坯连铸机的设计

介绍了马钢 2 5 0 mm× 1 40 0 mm直弧型坯连铸机设计指导思想、连铸机主要技术性能指标、工艺流程、设备组成及采取的技术措施 :无氧化浇注 ,连续弯曲矫直 ,二冷区气雾冷却及自动控制 ,在线短定尺二次切割 ,对称式双向出坯 ,防止测量基准移位和台阶式对弧样板等。     

25Cr3Mo3NiNb二次硬化钢冲击性能的研究

研究了二次硬化钢25Cr3Mo3NiNb的冲击韧度随回火温度和试验温度的变化.结果发现,试验钢在200℃回火时冲击韧度较高,300～600℃回火时冲击韧度值较低,600℃以上回火时冲击韧度值迅速升高,640℃回火时冲击韧度达到最高值55J/cm2,640℃以上回火时冲击韧度值有所降低.640℃回火后试验钢的冷脆转变温度为10℃,屈服强度为960MPa,可以满足兵器特种结构件高强度高韧性的要求.     

预应变对16MnR钢断裂韧性的影响SCIEI

本文实验发现预应变对16MnR钢的断裂韧性具有显著的影响,断裂过程中裂尖区域材料的组织结构发生了变化,裂纹在二次珠光体组织上扩展。16MnR钢断裂韧性的大小取决于碳原子的扩散及二次珠光体组织生成的难易程度。     

钛业分会2004年度工作总结

对贵金属二次资源的特点、来源、预处理方法以及金银铂钯等贵金属的回收利用方法等进行综合评述，提出了在无害化处置贵金属废料时应充分考虑回收利用工艺的全面性、尽可能以废治废、生物处理、集中处理、政府积极参与协调并加大投入，对于目前暂时无法做到无害化处置的贵金属废料，将这些废料暂时集中放置，滞后处理等有价值的建议。     

基于容量参数的二次电池嵌入型电极材料固相扩散系数的测定方法

介绍了一种以容量参数为主变量的测定锂二次电池中电极材料固相扩散系数的方法.该方法只需颗粒半径这一辅助参数,通过球型扩散模型建立了恒流-恒压充电容量(RPG)比,进一步发展成为容量间歇滴定技术(CITT).采用RPG法可在较宽的电压范围内测定嵌入型电极材料的平均固相扩散系数,实验结果重现性好.由RPG法测得0～1.5 V时锂离子在石墨电极中的平均固相扩散系数值为1.055×10-10cm2/s.由CITT技术测得锂离子在LiMn2 O4中的固相扩散系数在3.95 V和4.12 V左右存在个两个极小峰,且随着循环次数的增加,扩散系数值逐渐增大.