用新的电路形式提高HBT光调制器驱动电路的传输速率及性能

在传统光调制器驱动电路中,所用HBT截止频率的大小要达到驱动电路传输速率的4倍以上.文中在输出级采用共射共基HBT形式后,其器件的截止频率只需大于电路传输速率的2倍即可,从电路设计的角度降低了对所用器件的要求.文中分析了新的电路结构提高传输速率的原因并给出了模拟结果.同时新的电路结构也具有良好的热稳定性.     

一种高并行度的H.264帧内预测器的VLSI设计

分析了帧内预测的17种模式,对于每个4×4大小块的16个像素点的不同模式的预测公式之间的相同运算,采用数字强度缩减的方法去除计算的冗余,提出了一种高并行度的帧内预测器,可以每个时钟周期处理16个像素点的预测值。基于SMIC0.18μm工艺,用verilog对该设计进行了VLSI实现,综合后的电路的关键路径最大时延为10ns,电路规模不超过1.4万门,数据吞吐率可以达到1600Msamples/s。从实现结果来看,与采用可重构方法的设计相比,该设计在相同的并行度下减小了电路面积,简化了控制逻辑。     

AUTOCONER-338型自动络筒机的接头工艺与切疵有效性分析

介绍了AUTOCONER-338型自动络筒机空气捻接器的接头要求与影响接头质量的因素,并且就不同品种的纱线选用不同接头工艺进行了简单分析;介绍了如何评价络筒切疵有效性与影响切疵率的因素.通过以上2方面的分析介绍,及时调整设计与工艺,提高了生产效率,改善了布面质量.     

振动仿真在断路器设计中的应用

为解决某型航空断路器的耐振问题,利用MSC Adams/Vibration仿真工具对其建模与仿真. 找出影响耐振性能的主要原因,从而提高产品质量.     

平面药包抛掷爆破的漏斗特征解析

根据惠州港通用码头陆域平面药包抛掷爆破的实爆堆积测量分析成果 ,结合药包设计的主要参数 ,对平面药包产生的爆破漏斗的范围与形态、不同药包部位的残方比与抛掷率、药包的长抗比与圆柱体药包的应力波形演变关系予以解析 ,供硐室爆破的理论研究、模拟试验和总结条形药包特性时参考     

Preparation and properties of silicone‐containing poly(methyl methacrylate) gels

Poly(methyl methacrylate) (PMMA) gels with varying amounts of silicone and solvent and constant amounts of crosslinker were prepared by solution free radical crosslinking copolymerization of methyl methacrylate (MMA), ethylene glycol dimethacrylate (EGDM), tetraethoxysilane (TEOS) and vinyltriethoxysilane (VTES) comonomer systems. They were then studied in benzene at a total monomer concentration of 3.5 mol L^?1 and 70 °C. The conversion of monomer, volume swelling ratio, weight fraction and gel point were measured as a function of the reaction time, silicone concentration and benzene content up to the onset of macrogelation. Structural characteristics of the gels were examined by using equilibrium swelling in benzene, gel fraction and Fourier‐transform infrared (FTIR) analysis. The morphology of the copolymers was also investigated by SEM. Based on the obtained results, it was concluded that the FTIR data did not have the capacity to show the presence of the VTES or TEOS moiety in these kinds of copolymers. On the other hand, the variation of weight fraction of gel, W_g, and its equilibrium volume swelling ratio in benzene, q_v, exhibited the same behaviour as that of MMA/EGDM copolymers. Also, the dilution of the monomer mixture resulted in an increase in the gel point and swelling degree and a decrease in the percent of conversion and gel fraction. Finally, TEOS is not an ideal silicone compound for reaction in the MMA/EGDM copolymerization system, whereas VTES is a suitable silicone comonomer for this system and it has been proved useful. Copyright © 2005 Society of Chemical Industry     

光刻技术及其新进展

介绍了用于制作半导体集成电路的光刻工艺的概念、分类及发展过程，阐述了当前光刻工艺的主流，并重点介绍了极紫外光刻、X射线光刻、电子束光刻、离子束光刻、纳米图形转印等下一代光刻技术的特点及其面临的挑战。     

An investigation of crack closure and the propagation of semi-elliptical fatigue cracks in Q1N (HY80) pressure vessel steel

The results of an experimental investigation of the effect of crack closure on the propagation of semi-elliptical fatigue cracks are presented. Load-shedding fatigue threshold tests were carried out at stress ratios of 0.2, 0.35, 0.5 and 0.7. Crack closure was measured at the surface and depth positions using backface strain gauges, near-tip gauges, and a clip gauge. Differences between the surface and depth growth behaviour are explained by considerations of the effects of the transition from plane stress conditions at the surface to plane strain conditions at the depth. The effects of stress ratios are attributed largely to differences in the crack opening displacement, which result in asperities coming into contact to induce roughness-induced crack closure.     

Effect of load ratio on the deformation behaviour of fatigue crack tips

To investigate the change in the manner of plastic deformation at a fatigue crack tip under different loading conditions, the fresh surface area which is produced in one fatigue cycle at the crack tip was measured by an electrochemical method under various load ratios. The fresh surface area produced in each fatigue cycle is in proportion to the crack propagation rate in the Paris regime. This indicates that the crack tip geometry at K_max maintains a similar profile through the Paris regime. Furthermore, the fresh surface area is independent of load ratio at a given da/dN in the Paris regime. This suggests that the shape of the fatigue crack tip at K_max should be independent of load ratio at a given da/dN, and that the shape at K_min is also independent of load ratio, whereas the size of the deformed region at the crack tip is in proportion to da/dN.     

高电容比射频/微波MEMS膜开关的理论分析和数值模拟

建立了一个MEMS膜开关电容比理论模型，由于这个模型比较全面地考虑了开关阈值电压、维持电压、偏置电压和介质膜内的电场强度等因素对电容比的影响，因而能较为正确地反映开关的电容特性。用数值方法计算了影响开关电容比的因素，并对计算结果进行了分析和讨论。提出了使用脉冲电压作为偏置电压可以使介质膜gj的厚度减少到50nm，从而使开关的电容比增加到3800。最后，讨论了实现高电容比MEMS膜开关的可行性。