Ku波段10W功率PHEMT

报告了研制的 9.6mm栅宽双δ-掺杂功率 PHEMT,在 fo=1 1 .2 GHz、Vds=8.5 V时该器件输出功率3 7.2 8d Bm,功率增益 9.5 d B,功率附加效率 44.7% ,在 Vds=5～ 9V的范围内 ,该器件的功率附加效率均大于42 % ,两芯片合成 ,在 1 0 .5～ 1 1 .3 GHz范围内 ,输出功率大于 3 9.92 d Bm,最大功率达到 40 .3 7d Bm,功率增益大于 9.9d B,典型的功率附加效率 40 %。     

自适应RBF神经网络在CDMA移动通信上行链路功率控制中的应用研究

提出了一种自适应RBF神经网络功率控制方案。详细研究了该网络在DS-CDMA通信中，进行上行链路闭环功率控制(基于信扰比(SIR))的应用理论，给出了该网络参数的计算方法。最后用计算机仿真法模拟出该控制器的运行性能。结果表明基于SIR的自适应RBF神经网络功率控制器能自适应地调整移动台的发射功率，使基站接收信号的信扰比始终非常接近于一个常数，且有比定步长功率控制更小的SIR跟踪误差，从而可以降低接收信号的中断概率、提高信道容量。     

Copolymerization of bromophenylmaleimide with ethyl or butyl methacrylate

N‐p‐Bromophenylmaleimide (BrPMI) does not polymerize in solution by conventional free radical mechanism. However, it readily polymerized in bulk when mixed with a free radical initiator and heated in a microwave oven for 7–8 min. Copolymerization of ethyl methacrylate or butyl methacrylate with BrPMI was conducted in dioxane. The copolymers were characterized by IR and ¹H NMR spectroscopy and gel permeation chromatography. The monomer reactivity ratios were calculated by a non‐linear least‐square analysis. Thermal analysis indicated a great improvement in thermal stability of the copolymers compared with the methacrylate homopolymers. BrPMI was also polymerized in bulk in the DSC pan, which allowed the calculation of the activation energy of its polymerization. Copyright © 2003 Society of Chemical Industry     

转动玻璃圆筒激光器

本文介绍了转动玻璃圆筒激光器的设计及实验结果,得到了脉冲能量为13J,重复频率为15Hz的激光输出。电光转换效率为2.2％,斜效率为3.4％。     

Preparation of Ultra—fine Aluminum Nitride in Thermal Plasma

Ultra-fine aluminum nitride has been synthesized by the evaporation of aluminum powder at atmospheric-pressure nitrogen plasma in a hot-wall reactor.The average size of aluminum nitride particle is 0.11μm measured by scanning electric mirror(SEM),and the purity is at least over90% evaluated by X-Ray diffraction(XRD).The conversion of Al powder to aluminum nitride is strongly depended on the injection of NH3.Typical experimental parameters such as the feed rate of raw material,the flow rate of ammonia and the position of injecting aluminum powder into the reactor are given.     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

Synthesis and characterization of poly(siloxane-urethane)s

A series of polyurethane block copolymers based on hydroxy-terminated polydimethylsiloxane and poly(propylene glycol) soft segments of molecular weights 1818 and 2000, respectively, were synthesized. The hard segments consisted of 4,4′-diphenylnethane diisocyanate and 1,4-butanediol as the chain extender. Samples with different molar ratios were prepared. We tried to synthesize polydimethylsiloxane-based polyurethanes (PDMS-PU) containing a hard block as major fraction and a soft block as minor fraction for preparing toughened rigid systems. After a study of the pure polydimethylsiloxane-based polyurethane and poly(propylene glycol)-based polyurethane (PPG-PU), (mixed polyol)-based block copolymers and blends of PDMS-PU and PPG-PU were synthesized, and characterized by means of differential scanning calorimetry, tensile testing and scanning electron microscopy. In (mixed polyol)-based copolymers and lower hard-segment content blends, macro-phase separation occurred, but blends with higher hard-segment contents showed significant reduction in amounts of phase separation.     

Phenol novolac/poly(4- hydroxyphenylmaleimide) blend hardeners for DGEBA-type epoxy resin

Phenol novolac/poly (4-hydroxyphenylmaleimide) (PHPMI) blends were used as an epoxy resin hardener. The curing behavior of the above system and the thermal and mechanical properties of the cured epoxy resin were studied. It was not necessary to use a curing accelerator for this system, because PHPMI caused acceleration of the curing reaction. The curing mechanism of this system was investigated by using model compounds. Test pieces from the neat resins and the glass fiber reinforced resins were evaluated in terms of thermal and mechanical properties, respectively. It was found that heat resistance and mechanical properties were improved by increasing the amount of PHPMI in the hardener.     

高峰值功率重频脉冲固体激光器

综述了高峰值功率重频脉冲固体激光器的发展现状，对其中的Ｑ开关、腔倒空、锁模等窄脉冲技术和放大技术进行了分析，展示了高峰值功率重频脉冲固体激光器的发展前景。     

钨系延期药预点火反应机理研究

通过程控升温模拟点火条件，根据ＤＳＣ图谱分析，找出主要反应区的温度范围。研究结果表明，钨系延期药预点火反应是一个真正的固－固反应。