大庆长垣南部油田周期注水的做法及效果

本总结了大庆长垣南部周期注水的做法和效果。实践证明，在低渗透，薄油层，单井低注低产的油田上实施周期注不仅能够改善油田开发状况，而且也为低注井的冬季管理提供了方便条件。     

Design and implementation of fast charging circuit for repetitive compact torus injector

A novel circuit for compact torus (CT) injector operated at high repetition rates has been developed. The core technology adopted in the present work is to charge a large storage capacitor bank and quickly charge the CT capacitor bank through a stack of insulated-gate bipolar transistors (IGBTs). A system consisting of IGBTs and slow banks for the repetitive operation has been developed and installed for each discharge circuit of the University of Saskatchewan Compact Torus Injector (USCTI). A repetition rate up to 1.7 Hz and a burst of 8 CTs have been achieved.     

Point-Source Helicity Injection Current Drive System for the Pegasus Toroidal Experiment

Recent Pegasus experiments are developing solenoid-free startup techniques using point-source magnetic helicity injection. These plasma sources, called “plasma guns”, ionize a stream of gas in a discharge channel, and bias this channel with respect to an external electrode, driving current along the plasma stream, which relaxes into a tokamak-like equilibrium. The relaxed discharges formed by these injectors exhibit high current amplification, which is the ratio of total toroidal current to the gun-driven current. The development and present design of these injectors are described, and time traces from a typical discharge are presented.     

玻璃纤维/大麻纤维增强聚丙烯混杂复合材料的力学性能和断裂特征(英文)

目前在土木工程,建筑,汽车等领域里使用的复合材料中,玻璃纤维是用量最大的增强材料。由于保护地球环境的呼声日趋高涨,天然纤维被期待着代替源于石油而且再利用困难的玻璃纤维,成为绿色复合材料的必要材料之一。本文通过注射成型工艺制作了玻璃短纤维,大麻短纤维以及混杂型纤维增强复合材料,并在拉伸实验中应用两种不同频率的声发射技术检测了拉伸断裂特性。实验发现,随着大麻纤维的加入和混杂复合材料绿色度的增加,复合材料的拉伸弹性模量随之线性增大,而拉伸强度基本保持不变。当大麻纤维的含量超过20wt%的时候,拉伸强度开始降低。在不同频率的声发射实验中,混杂型复合材料的声发射事件的产生都比单一纤维增强型复合材料要来的晚,也就是说,纤维的混杂有助于推迟微裂纹的产生。     

Densification and mechanical properties of boron carbide with micro-hole array by micro-powder injection molding

For the purpose of obtaining fully dense B₄C with micro hole array of high quality and precision, synthesis of B₄C powders were carried out by micro powder injection molding. Five kinds of additive systems were used and their influences on mechanical properties were investigated. The relative density, Vickers hardness, bending strength, and fracture toughness of the B₄C ceramics with BS10AY additive sintered at 2000 °C for 2 h could reach 97.56%, 3580.4 HV, 355.3 MPa and 5.87 MPa m^1/2, respectively. The temperature was generally 100–200 °C lower than reported temperatures which was attributed to the additives. The improvement in mechanical properties was attributed to grain refinement. A mixture of intragranular and transgranular fractures occurred due to the fine microstructures and the additive systems in the B₄C ceramics after sintering. Micro-hole array with the diameter of 450 μm and the length-diameter ratio of more than 8 were obtained. The inhomogeneous filling of feedstock from the substrate to the thin wall between two adjacent micro holes caused the inhomogeneous shrinkage of the substrate and micro holes.     

水性丙烯酸酯乳液包膜尿素研究

水性聚合物乳液包膜肥料技术在提高肥料利用率、有效控制农业污染方面发挥重要作用。采用预乳化半连续滴加的种子乳液聚合工艺合成水性丙烯酸酯乳液、高压喷枪喷涂包裹尿素制得包膜尿素;讨论了不同聚合硬软单体质量比、油水质量比、引发剂用量、乳化剂用量对乳液性质及包膜效果的影响,当聚合硬软单体质量比为48.0∶52.0、油水质量比为100∶120、w(引发剂)为0.5%、w(乳化剂)为2.4%时,包膜尿素缓释性较好。     

尿素装置节能技术改造实例分析

介绍了尿素装置节能技术改造的方案。本方案实施后,尿素装置节约蒸汽98400 t/a,节约循环水2496万t/a,节约合成氨960t/a,折算节标煤共计16221.02 t/a,节能效益明显,其综合能耗可达到先进水平。