大庆油田三类油层聚合物驱注入速度研究

注入速度是影响聚合物驱开发效果的重要指标,而由于假设条件的局限性,数值模拟方法无法体现聚合物溶液弹性对注入速度的影响。为了确定大庆油田三类油层合理注入速度,通过不同注入速度条件下的天然岩心驱油试验,对水驱和聚合物驱驱油效率进行了研究,结果表明,聚合物驱驱油效率提高值随驱替速度的变化可由二次多项式来表示。依据此关系式,由势的叠加理论得到的流体在油层中的渗流速度的基础上,建立了该类油层合理注入速度模型,并给出大庆油田三类油层在100 m注采井距下的合理注入速度为0.288 PV年/,该方法对现场开发方案编制有重要指导意义。     

咪唑封端扩链脲改性环氧树脂E-51/酸酐MTHPA体系性能研究

以端羟基聚环氧丙烷1000，甲苯二异氰酸酯（TDI），2－甲基咪唑为原料，合成了扩链脲TI，利用DSC，动态热机械分析仪DMA，冲击试验机及扫描电镜（SEM）等手段对TI改性的环氧树脂E－51／甲基四氢化邻苯二甲酸酐（MTHPA）固化体系的反应活性，动态力学行为，冲击性能，断裂面形态结构进行了系统研究，结果表明，改性后的E－51／MTHPA体系反应活性明显提高，固化反应峰顶温度较未改性体系降低160℃－200℃，固化反应的表观活化能由未改性体系的160．3kJ/mol降至63kJ/mol-87kJ/mol，同时与未改性体系相比，经过改性的环氧树脂固化体系冲击强度有较大的提高，在TI含量为5％时体系的玻璃化转变温度Ts达到最高，各改性体系冲击断面呈韧性断裂。     

Numerical Filling Simulation of Injection Molding Using Three-Dimensional Model

1 Introduction During injection moulding, the rheological response of polymer melts is generally non-Newtonian and nonisothermal with the position of the moving flow front. Because of these inherent factors, it is difficult to analyze the filling process. Therefore, simplifications usually are used. For example, in middle-plane technique and dual domain technique [1], because the most injection molded parts have the characteristic of being thin but generally of complex shape, the Hele-Shaw …     

THE FLOW PRODUCED IN PARTICLE-SUSPENSION BY AN INFINITE ROTATING DISK:SERIES SOLUTION

To the flow produced in particle-suspension by a rotating disk of infinite extent,the asymptotic behavior at infinity is analyzed.A corresponding series solution is presented.It isshown that this approach yields widely valid solutions of high accuracy for all the cases in whichthat suction or weak injection at the disk surface exists.For the cases that strong injection or par-ticle-free band exists,the series method fails.     

Volatile organo-halogen trace analysis in beverages by thin-layer headspace enrichment and electron-capture gas-chromatography

Applicability of thin-layer headspace (TLHS) procedure giving an aqueous concentrate and also classical purge and trap (PT) in off-line mode to isolate and enrich volatile organohalogen compounds in common beverages was tested. Both enrichment tech-niques were used in combination with gas chromatography – electron capture detection (GC-ECD). TLHS, combined with direct aqueous injection (DAI)-GC-ECD, proved applicable in the determination of volatile organohalogen compounds in all studied beverages, while the PT in a version with no preliminary sample pre-treatment was of limited applicability. Detection limits of the TLHS-based procedure were in the order of 1 ppt. Content of volatile organohalogen compounds in a number of beverages available on the Polish market including mineral waters, beers, juices, carbonated and non-carbonated soft drinks, etc. was determined by means of TLHS-DAI-GC-ECD.     

岩心PI值试验研究及应用

主要论述了在多功能采油化学用剂评价仪上进行的岩心ＰＩ值试验的步骤，现象及结论。重点考察了岩心ＰＩ值与渗透率、流量及注入截面面积的关系；平行管岩心复合ＰＩ值和其中单管岩心ＰＩ值的关系。     

大庆长垣南部油田周期注水的做法及效果

本总结了大庆长垣南部周期注水的做法和效果。实践证明，在低渗透，薄油层，单井低注低产的油田上实施周期注不仅能够改善油田开发状况，而且也为低注井的冬季管理提供了方便条件。     

稠油油藏的注汽量预测

利用HCZ预测模型，可对已开发油田的年产量和累计产量进行全程预测，并且在实际应用中取得了较好的预测结果。本文结合稠油田的实际情况，推导出HXZ预测模型在热采中注汽参数的预测公式。结合曙光油田曙1－7－5块的开发数据进行了预测，效果较好。     

涂硫尿素

涂硫尿素（ＳＣＵ）是一种缓效氮肥，是在普通尿素外面喷涂硫、密封剂和调理剂而制成。它在国外已成功使用多年．本文叙述了涂硫尿素的性质、生产过程、肥效和经济效益，供国内读者参考。     

雁翎油田注氮气提高采收率工艺技术

在现有的提高采收率方法中,注气驱是应用较广、效果较好的方法,特别是注氮气驱由于其气源广泛、价廉经济、无腐蚀性,以及要求的油藏地质结构特征和原油的物理性质等因素的变化范围广泛等特产,这种提高采收率的方法应用的最为普及,代表了目前提高采收率的发展方向。结合雁翎油田实例,简要介绍了注氮气提高采收率的机理、注气井组建设、制氮工艺及注气后的采油完井方式、方法。