砂岩油藏注水井深部酸化技术

吐哈油田长期注水开发后,注入水外源性伤害和地层内源性伤害不断在地层深部累积,采用常规酸化措施效果不理想。为此,通过长岩心污染模拟实验,研究了深部污染的污染特征及酸化解堵机理,通过解堵液缓速和工艺过程的综合应用实现深部解堵。应用AcidGuide专家系统对单井进行全面的污染诊断分析,并进行了参数优化设计,形成了适应吐哈油田深部酸化解堵的技术体系,现场应用取得良好效果,为类似低渗透油藏水井增注措施提供参考。     

稠油井注汽系统的热效率分析

建立了热采注汽系统热效率的计算模型。根据XX油田数据计算了2个注汽系统的热效率。提出了提高注汽系统热效率的三项措施：（1）降低锅炉的过剩空气系数；（2）按最大允许热损失设计地面输汽管线的保温层厚度；（3）使用视导热系数小的隔热油管，按箍增加隔热结构，防止热封隔器的泄漏等。     

Phase separation studies in RIM polyurethanes catalyst and hard segment crystallinity effects

Polyurethanes were prepared from pure 4,4′-diphenylmethane diisocyanate (MDI), 1,4-butane diol (BDO) or 1,2-ethane diol (EDO) and α,ω-hydroxyl poly(propylene oxide) (PPO) by reaction injection moulding (RIM). Hard segment (MDI + BDO or EDO) level was 45–50 wt%. The PPO had about 20% ethylene oxide copolymerized in at the chain ends to provide 80% primary OH end groups. M_n was varied from 2000 to 4000. Dibutyl tin dilaurate catalyst and mould temperature were varied. Dynamic mechanical, wide-angle X-ray, differential scanning calorimeter, molecular weight and tensile elongation measurements were made on the RIM polyurethanes. At low reaction rates (low catalyst or temperature) highly crystalline, well phase separated but low molecular weight polymers were produced. At high catalyst or temperature levels more poorly phase separated but high molecular weight, tough polymers resulted. Higher M_n PPO gave better phase separation and EDO gave higher melting temperatures. Preventing hard segment crystallinity by substituting asymmetric MDI or glycols resulted in phase compatibility.     

Observers for linearly unobservable nonlinear systems

We provide a method for constructing local observers for some nonlinear systems around a critical point where the linearization is not observable or not detectable. Two examples are provided to illustrate the results of the paper.     

耐高温绝缘GFRP管的真空辅助树脂传递成型工艺研究

阐述了耐高温绝缘GFRP管的成型工艺及原材料选择，并对影响成型工艺的主要因素作了理论分析及试验验证。研究表明，以TDE－85／DDS体系为为基体，以无碱无捻玻璃纤维方格布为增强材料，用VARTM工艺成型的石油勘探高性能平衡管完全满足技术要求。     

注聚井注入状况诊断方法研究

在室内试验和动态分析的基础上，对引起注聚井注入困难的原因进行了分析，提出了利用单井动态预测结果和实际注入动态曲线对比判断聚合物注入状况的方法，建立了预测注聚井注入动态的预测模型，并对数值模拟计算结果进行了分析。同时还评价了现场应用效果。通过数值模拟和实际注入动态曲线对比，可以初步判断待措施井有无近井地带堵塞，为提高注聚井压解堵措施的有效性奠定了基础。     

凝析气藏物质平衡方程的改进与应用

为了提高凝析气藏油气采收率，通常采用目前最有效的循环注气保持地层压力的开采方式。在此开采方式下，直接采用气藏物质平衡方程进行地质储量计算将出现很大偏差。针对这种情况，将气藏物质平衡方程进行了改进，得到凝析气藏在注气开发方式下的物质平衡方程。     

提高特高含水期油藏采收率的方法及应用效果

针对胜索油田二区9-10单元的层间非均质和平面非均质性，运用水动力学方法，采用周期注水及增压注水改善单元的水驱油效果。经过6a的实施，单元的开发形势趋好，单元采收率提高9.62%，增加可采储量341.5kt，对同类型非均质性油藏改善水驱油效果，提高最终采收率具有借鉴意义。     

Structure and properties of injection‐molded polypropylenes with different molecular weight distribution and tacticity characteristics

Two series of polypropylenes with different molecular weight distribution and tacticity characteristics were injection molded into flexural test specimens by varying cylinder temperature and the effects of the molecular weight distribution and tacticity on the structure and properties of the moldings were studied. Measured propertied were flexural modulus, flexural strength, heat distortion temperature, Izod impact strength, and mold shrinkage and structures studied were crystallinity, the thickness of skin layer, a*‐axis‐oriented component fraction and crystalline orientation functions. The relations between the structures and properties were also studied. It was found that the molecular weight distribution and tacticity characteristics affect the properties mainly through the molecular orientation and crystallinity, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2142–2156, 2002     

PVC四通管注射模设计

介绍了PVC四通管注射模设计 ,阐述了弯型芯的旋转抽芯过程以及模具顶出、回程及冷却系统设计。实践证明 ,该模具结构合理 ,生产的塑件可以满足设计要求