离心式空压机轴承技术改造

针对离心式空压机各级轴振动值超标的现象进行技术攻关,解决了制约装置安全平稳生产的瓶颈问题。     

雅克拉凝析气田高压脱水工艺的成功应用

雅克拉凝析气田位于新疆阿克苏境内，2005年11月29日建成投运的260×10⁴m³/d雅克拉集气处理站是目前中石化最大的高压凝析气处理装置。该站的高压分子筛脱水工艺为两塔流程，采用差压再生（吸附压力5.9 MPa、再生压力2.8 MPa）、再生气自动回收工艺技术，并采用时序控制程序自动切换，具有工艺简单可靠、自动化程度高、热能利用率高、脱水露点深度高、操作维护简单、投资较少、运行成本低等优点，自建成投产以来运行稳定，效果十分显著。该工艺装置的成功应用，对类似脱水装置设计、操作具有一定参考价值。     

高压低温先导式安全阀的设计

介绍了一种某试验系统用高压低温先导式安全阀,主要从工作原理、结构特点、材料的选用、结构特点、试验等方面进行阐述。     

漫谈钢铁企业用空分装置的流程选择

钢铁企业的氧气厂要深入了解本企业的用氧情况及周边市场的需要，据此确定拟新增空分装置的设计参数，选定最适宜的空分流程。探讨了空分流程选择时要考虑的几个方面。介绍了一种对空分装置的投资和长期运行费用之间进行经济性分析的定量计算公式，并得出了四点结论。     

Heat transfer of a row of three butane/air flame jets impinging on a flat plate

Experiments were performed to investigate the heat transfer characteristics of a row of three premixed, laminar, butane/air flame jets impinging on a water-cooled flat plate. The between-jet interference was found to reduce the heat transfer rate in the jet-to-jet interacting zone due to the depressed combustion. The interference became stronger when the jet-to-jet spacing and/or the nozzle-to-plate distance were/was small. The positive pressure existed in the between-jet interacting zone caused the asymmetric flame and heat transfer distribution of the side jet. The meeting point of the spreading wall jets of the central and the side jets did not occur at the midpoint of the neighboring jets, but at a location shifted slightly outwards. The maximum local heat flux and the maximum area-averaged heat flux occurred at a moderate nozzle-to-plate distance of 5d with a moderate jet-to-jet spacing of 5d. The lowest area-averaged heat flux was produced when both the jet-to-jet spacing and the nozzle-to-plate distance were small. Comparing with a single jet under the same experimental conditions, the heat transfer rates in both the stagnation point and the maximum heat transfer point were shown to be enhanced in a row of three-jet-impingement system. The present study provided detailed information on the heat transfer characteristics of a row of three in-line impinging flame jets, which had rarely been reported in previous study.     

55t/h锅炉技术改造成功经验

介绍了35t／h锅炉扩容改造为55t／h非标锅炉的技术成功经验。从增加锅炉的容积、受热面面积、燃烧器喷嘴改造三个方面介绍了对锅炉本体的改造，改造后实现了锅炉的水位、汽温及燃烧自动调节，提高了锅炉的热效率为以后的锅炉扩容改造提供了实践经验。     

利用测井资料预测塔河油田地层破裂压力

针对塔河油田奥陶系碳酸盐岩油藏 ,介绍了地层破裂压力预测和地层裂缝高度预测的基本原理 ,选择了塔河油田 4口井的资料进行了破裂压力和裂缝高度预测的成果处理。为塔河油田奥陶系碳酸盐岩储层改造提供了较为可靠的施工参数     

Case Study of an Aerosol Explosion and a Method to Determine Explosion Temperatures

A failure analysis case study is presented for a two-piece aerosol containing tetrafluoroethane, commonly referred to as Refrigerant 134a. A gentleman was preparing to recharge the air conditioning system of an automobile when the bottom exploded off the aerosol container, propelling the body of the aerosol container like a rocket, which hit the man in the eye and blinded him in that eye. The aerosol was never connected to the air conditioner, therefore backpressure from the air conditioner (AC) compressor was ruled out as a cause for the explosion. The objective of the study was to determine why the aerosol exploded. Several recently developed test methods were used, including two types of heat-to-burst tests and a puncture chamber to measure the pressure-versus-temperature behavior of aerosols. More common test methods were also used, such as water bath pressure tests, hydro pressure burst tests, pneumatic pressure burst tests, hardness measurements, weight measurements, metallography, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and an accident scenario recreation. A semi-empirical correlation between the hardness and weights of the container bottoms was used to determine the explosion temperature and/or pressure. This semi-empirical correlation agrees in principle with an analysis of the explosion pressures using finite-element analysis (FEA). The root cause for the explosion was determined to be a lack of strength of the bottom of the two-piece aerosol coupled with heating the aerosol to temperatures significantly above room temperature.     

基于PLC的焦炉集气管压力专家控制系统

通过对焦炉煤气集气管压力系统的分析研究，提出基于专家系统的集气管压力协调控制方案，使得系统在传统PID控制的基础上，能够按照系统实际运行状况智能选择控制策略。全部系统基于西门子S7系列PLC构成，并采用PROFIBUS电缆组成总线型网络。     

静压下ZnS：Te中Te等电子陷阱的发光

研究了4块ZnS：Te薄膜样品(Te组分从0．5％到3．1％)的光致发光谱在常压下的温度特性．对于Te组分较小的2块样品观察到2个发光峰，分别来自Te1和Te2等电子陷阱；而对Te组分较大的2块样品则只观察到1个来自Te2等电子陷阱的发光．我们还研究了这些发光峰在低温1．5K下的流体静压压力行为．观察到与Te1有关的发光峰压力系数比ZnS带边的要大很多，而与Te2有关的发光峰压力系数则比带边小．根据Koster-Slater模型，价带态密度半宽随压力的增加是Te1中心有较大压力系数的主要原因，而Te1和Te2中心的不同压力行为则是由于压力对两者缺陷势增强的不同效果引起的．