Sensorless control of synchronous reluctance motors using on‐line parameter identification method not affected by position estimation accuracy

This paper presents a novel on‐line parameter identification method for sensorless control of Synchronous Reluctance Motors (SynRMs). Although conventional sensorless control methods based on mathematical models usually need some complex measurements of motor parameters in advance, the proposed identification method does not require them and can be realized on‐line. The proposed method identifies motor parameters under sensorless control, so rotor position and velocity cannot be used to identify these parameters. However, the proposed method does not need rotor position and velocity, and identified parameters are not affected by these estimation errors. The sensorless control using identified motor parameters is realized, and the effectiveness of the proposed method is verified by experimental results. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(3): 62–69, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20258     

Minimum switching control for adaptive tracking

The switching adaptive control method has been used for quite a few years to solve the adaptive stabilization and model reference adaptive control problems. However, a serious problem with the switching control method is that the number of ‘candidate’ controllers can potentially be very large, especially for multi‐input–multi‐output systems. In this paper, we consider a class of minimum‐phase multi‐input–multi‐output plants with some mild compactness assumptions. Given any polynomial reference input, we provide a switching control law which guarantees exponentially stability of the closed‐loop system with exponential tracking performance. The main contribution of the paper is that we give the minimum number of candidate controllers required for switching. In particular, the number is equal to 2 for single‐input–single‐output plants (one for each sign of the high‐frequency gain), and is equal to 2^m for m‐input–m‐output plants. That is, the number is independent of the degree and the relative degree of the plant. Copyright © 2006 John Wiley & Sons, Ltd.     

A novel method of suppressing the inrush current of transformers by using a series‐connected voltage‐source PWM converter

This paper proposes a novel method of suppressing the inrush current of transformers. A small‐rated voltage‐source PWM converter is connected in series to the transformers through a matching transformer. As the connected PWM converter serves as a resistor for the source current, no inrush phenomena occurs. The required rating of the PWM converter, which serves as the damping resistor for the inrush phenomena, is 1/400 that of the main transformers in single‐phase circuits. In three‐phase circuits, it is 1/900. The basic principle of the proposed method is discussed. Digital computer simulation is implemented to confirm the validity and excellent practicability of the proposed method using the PSCAD/EMTDC. A prototype experimental model is constructed and tested. The experimental results demonstrate that the proposed method can perfectly suppress the inrush phenomena. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(4): 56–65, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20174     

A novel robust current control approach using adaptive line enhancer for three‐phase current‐source active power filter

An effective system control method is presented for applying a three‐phase current‐source PWM converter with a deadbeat controller to active power filters (APFs). In the shunt‐type configuration, the APF is controlled such that the current drawn by the APF from the utility is equal to the current harmonics and reactive current required for the load. To attain the time‐optimal response of the APF supply current, a two‐dimensional deadbeat control scheme is applied to APF current control. Furthermore, in order to cancel both the delay in the two‐dimensional deadbeat control scheme and the delay in DSP control strategy, an Adaptive Line Enhancer (ALE) is introduced in order to predict the desired value three sampling periods ahead. ALE has another function of bringing robustness to the deadbeat control system. Due to the ALE, settling time is made short in a transient state. On the other hand, total harmonic distortion (THD) of source currents can be minimized compared to the case where ideal identification of the controlled system can be made. The experimental results obtained from the DSP‐based APF are also reported. The compensating ability of this APF is very high in accuracy and responsiveness although the modulation frequency is rather low. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20014     

Drying of Probiotics: Optimization of Formulation and Process to Enhance Storage Survival

This work describes how probiotic bacteria can be dried at low temperature in two steps, combining spray drying and vacuum drying, in order to enhance their survival during storage. A sufficient number of dried probiotics survived storage for more than 3 months at 30°C, if an appropriate combination of protein and carbohydrate was selected as carrier and storage conditions were maintained optimal. The use of soy protein and maltodextrin or skim milk and arabic gum resulted in the best survival rates of probiotics during storage. No evident difference was found between different spray dryer configurations, although a cocurrent flow was preferred.     

V. Yeast sequencing reports. Identification of a gene encoding a new Ypt/Rab-like monomeric G-protein in Saccharomyces cerevisiae

A Saccharomyces cerevisiae sequence cloned by serendipity was found to encode a protein that is a new member of the Ypt/Rab monomeric G-protein family. This sequence shows high homology to the yeast genes SEC4 and YPT1 and, like SEC4 and YPT1, is essential for viability. The sequence was localized to chromosome V based upon hybridization to pulse-field gel-separated yeast chromosomes. The sequence has been deposited in the GenBank data library under Accession Number L17070.     

Mesh‐independent p‐orthotropic enrichment using the generalized finite element method

This paper is aimed at presenting a simple yet effective procedure to implement a mesh‐independent p‐orthotropic enrichment in the generalized finite element method. The procedure is based on the observation that shape functions used in the GFEM can be constructed from polynomials defined in any co‐ordinate system regardless of the underlying mesh or type of element used. Numerical examples where the solution possesses boundary or internal layers are solved on coarse tetrahedral meshes with isotropic and the proposed p‐orthotropic enrichment. Copyright © 2002 John Wiley & Sons, Ltd.     

A new family of yeast genes implicated in ergosterol synthesis is related to the human oxysterol binding protein

We have identified three yeast genes, KES1, HES1 and OSH1, whose products show homology to the human oxysterol binding protein (OSBP). Mutations in these genes resulted in pleiotropic sterol-related phenotypes. These include tryptophan-transport defects and nystatin resistance, shown by double and triple mutants. In addition, mutant combinations showed small but apparently cumulative reductions in membrane ergosterol levels. The three yeast genes are also functionally related as overexpression of HES1 or KES1 alleviated the tryptophan-transport defect in kes1Δ or osh1Δ mutants, respectively. Our study implicates this new yeast gene family in ergosterol synthesis and provides comparative evidence of a role for human OSBP in cholesterol synthesis.     

XV. Yeast sequencing reports. Isolation and DNA sequence of the STE13 gene encoding dipeptidyl aminopeptidase

We have isolated a mutant which exhibits partial constitutivity for a -specific gene expression in α cells. The wild-type gene was cloned and demonstrated to be allelic to the STE13 gene, which encodes the dipeptidyl aminopeptidase involved in processing of the α-factor prepropheromone. Thus, the mating defect of the ste13 mutations in α cells may result both from the production of incompletely processed α-factor and from the increased expression of a -specific genes. The STE13 open reading frame of 931 amino acids contains a putative membrane-spanning segment near its amino terminus and is 31% identical to a second yeast dipeptidyl aminopeptidase (DAP2). A null mutant of STE13 has been constructed: it is viable and sporulation-proficient. The sequence has been deposited in the GenBank data library under Accession Number L21944.