Hybrid gas-to-particle conversion and chemical vapor deposition for the production of porous alumina films

Porous alumina films can be found in a wide variety of materials, including filters, thermal insulation components, dielectrics, biomedical and catalyst supports, coatings and adsorbents. Production methods for these films are as equally diverse as their applications. In this work, a hybrid process based upon chemical vapor deposition and gas-to-particle conversion is presented as an alternative technique for producing porous alumina films, with the main advantages of solvent-free, low substrate-temperature operation. In this process, nanoparticles were produced in the vapor phase by reaction of aluminum acetylacetonate in the presence of oxygen. Downstream of this reaction zone, these nanoparticles were collected via thermophoresis onto a cooled substrate, forming a porous film. Some deposited films were subjected to post-processing in the form of annealing in air. Fourier-transform infrared spectra and X-ray energy-dispersive spectroscopy analysis confirmed the production of alumina at processing temperatures above 973 K. X-Ray diffraction revealed that the films were amorphous. Film thickness, ranging from 30 to 250 μm, and the average deposition rate were determined from scanning electron microscopy results. From transmission electron microscopy, the average primary particle size was determined to be approximately 18 nm and the formation of nanoparticle aggregates was evident. Annealing of the films at temperatures ranging from 523 to 1173 K in the presence of air did not have an effect on particle size. The specific surface area of the powder composing the films ranged from 10 to 185 m² g⁻¹, as determined from nitrogen gas adsorption by the Brunauer–Emmett–Teller method.     

同杆并架双回线基于电流突变量的综合选相

相电流差突变量选相元件在单回线故障中具有良好的选相性能，但在同杆双回线跨线故障中可能误选相。利用六序故障分量的分析方法，分析了相电流突变量在同杆双回线跨线故障中的幅值和相位特征，给出了其相位比相方程。在此基础上，提出了一种运用测量阻抗和方向元件相结合的综合选相方法，并给出了选相流程图。仿真结果表明，在双回线简单故障和跨线故障时，基于单回线单端电气量的同杆并架双回线综合选相方法具有较理想的选相性能。     

大型空分设备循环冷却水处理方法的对比研究

武钢氧气公司在大型空分设备循环冷却水系统中,采用化学法和物理法进行水处理效果的实践探索,从原理和监测数据上进行了对比、分析研究,确认物理法具有高效除垢、防垢、杀菌灭藻、缓蚀以及净化等功能,可以取代化学法进行循环水处理。     

活性污泥数学模型入流组分测定及应用

阐述了活性污泥1号模型人流组分的分析方法，并用这些方法测定了西安市城市污水水质。实验结果表明测定方法操作简单、准确可靠，能为利用模型进行污水处理厂的设计、模拟及管理提供入流组分分析依据，     

A novel technique to prepare LiNbO3 at low temperature

Fresh niobium hydroxide was first precipitated from NbF₅ solution using an aqueous ammonium hydroxide under basic conditions. Then a simple procedure of mixing lithium and niobium hydroxides together and heating at a low temperature (400 °C) produced pure ultrafine single phase LiNbO₃ (LN). In the literature, this is the lowest temperature so far reported on the formation of LN. The phase content and lattice parameters are determined by X-ray diffraction (XRD). The average particle size and morphology were studied by transmission electron microscopy (TEM).     

Chemical vapor deposition of amorphous ruthenium-phosphorus alloy films

Chemical vapor deposition growth of amorphous ruthenium-phosphorus films on SiO₂ containing ∼ 15% phosphorus is reported. cis-Ruthenium(II)dihydridotetrakis-(trimethylphosphine), cis-RuH₂(PMe₃)₄ (Me = CH₃) was used at growth temperatures ranging from 525 to 575 K. Both Ru and P are zero-valent. The films are metastable, becoming increasingly more polycrystalline upon annealing to 775 and 975 K. Surface studies illustrate that demethylation is quite efficient near 560 K. Precursor adsorption at 135 K or 210 K and heating reveal the precursor undergoes a complex decomposition process in which the hydride and trimethylphosphine ligands are lost at temperatures as low at 280 K. Phosphorus and its manner of incorporation appear responsible for the amorphous-like character. Molecular dynamics simulations are presented to suggest the local structure in the films and the causes for phosphorus stabilizing the amorphous phase.     

Formation of mushroom-like ZnO microcrystals through a solution calcination process

Mushroom-like ZnO microcrystals have been prepared via a solution calcination route, using Zn(NO₃)₂ as Zn source in the absence of any surfactants, templates or catalysts. This is the first example to prepare mushroom-like crystals as semiconductors, which are expected to show particular physical properties. The ZnO products were investigated by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy and photoluminescence (PL) spectrum measurements. A suitable concentration of Zn(NO₃)₂ solution was important for the growth of the mushroom-like products. The reported synthetic procedure is straightforward and inexpensive, and thus can be readily adopted to produce large quantities of mushroom-like ZnO microcrystals.     

SECANT-FUZZY LINEAR REGRESSION METHOD FOR HARMONIC COMPONENTS ESTIMATION IN A POWER SYSTEM

In order to avoid unnecessary damage of electrical equipments and installations,high quality power should be delivered to the end user and strict control on frequency should be made, Therefore, it is important to estimate the power system's harmonic components with higher accuracy. This paper presents a new approach for estimating harmonic component in a power system using secant - fuzzy linear regression method. In this approach the non - sinusoidal voltage or current waveform is written as I linear function. The coefficient of this function is assumed to be fuzzy number with a membership function that has center and spread value. The time dependent quantity is written as Taylor series with two different time dependent quantities. The objective is to use the sample obtained from the transmission line to find the power system harmonic components and frequencies. We used an experimental voltage signal from a sub power station as a numerical test.     

Corrosion Condition Evaluation at Muddy Creek Bridge

Corrosion rates were measured at the exposed spots of rebars near three corners of Muddy Creek Bridge located in northern West Virginia using a 3LP device. Also, chloride contents of the concrete samples taken from the vicinity of the spots were analyzed using a wet chemical method that had been developed in this study. The average corrosion rate over the three spots was 4.66 mA/m2, which is in the range of corrosion damage possible in 10–15 years. The average chloride content of the concrete over the three spots was 703 parts per million (ppm), which is well above the threshold limit value of 260 ppm. Although the corrosion rate measurement method using a 3LP device is by manual operation, it is found to be reliable and effective, and, thus, recommended for future studies of this kind of research. The wet chemical method developed in this study is found to be effective.     

用高分子复合材料修复轧管机组大型构件

介绍采用高分子复合材料修复用于钢管生产的轧管机组大型构件的方法。重点介绍机架轴承座孔的修复工艺流程 ,修复定位 ,技术操作要点及修复效果。