SECANT-FUZZY LINEAR REGRESSION METHOD FOR HARMONIC COMPONENTS ESTIMATION IN A POWER SYSTEM

In order to avoid unnecessary damage of electrical equipments and installations,high quality power should be delivered to the end user and strict control on frequency should be made, Therefore, it is important to estimate the power system's harmonic components with higher accuracy. This paper presents a new approach for estimating harmonic component in a power system using secant - fuzzy linear regression method. In this approach the non - sinusoidal voltage or current waveform is written as I linear function. The coefficient of this function is assumed to be fuzzy number with a membership function that has center and spread value. The time dependent quantity is written as Taylor series with two different time dependent quantities. The objective is to use the sample obtained from the transmission line to find the power system harmonic components and frequencies. We used an experimental voltage signal from a sub power station as a numerical test.     

Corrosion Condition Evaluation at Muddy Creek Bridge

Corrosion rates were measured at the exposed spots of rebars near three corners of Muddy Creek Bridge located in northern West Virginia using a 3LP device. Also, chloride contents of the concrete samples taken from the vicinity of the spots were analyzed using a wet chemical method that had been developed in this study. The average corrosion rate over the three spots was 4.66 mA/m2, which is in the range of corrosion damage possible in 10–15 years. The average chloride content of the concrete over the three spots was 703 parts per million (ppm), which is well above the threshold limit value of 260 ppm. Although the corrosion rate measurement method using a 3LP device is by manual operation, it is found to be reliable and effective, and, thus, recommended for future studies of this kind of research. The wet chemical method developed in this study is found to be effective.     

用高分子复合材料修复轧管机组大型构件

介绍采用高分子复合材料修复用于钢管生产的轧管机组大型构件的方法。重点介绍机架轴承座孔的修复工艺流程 ,修复定位 ,技术操作要点及修复效果。     

单壁碳纳米管的制备及生长特性研究

采用Fe/MgO作为催化剂 ,催化裂解CH4制备了较纯的单壁碳纳米管 ,用TEM和Raman对碳纳米管进行了表征 ,对不同生长温度下制备的碳纳米管Raman径向呼吸振动峰 (RBM)进行了分析 ,研究了生长温度对单壁碳纳米管生长特性和结构特性的影响     

高速电路中地电流的影响及其对策

从理论上分析了产生地电流干扰的原因，从而在实践上提出了一些经常被忽略，却是行之有效的方法来减小地电流的干扰，设计出高质量的电路。     

The aligned Si nanowires growth using MW plasma enhanced CVD

New and simple modification of vapor-liquid-solid process for Si nanowires growth based on microwave plasma enhanced chemical vapor deposition that uses solid-state Si target as a source of Si atoms was developed. The method was temperature and pressure controlled evaporation of solid phase of Si source in hydrogen microwave plasma. Aligned growth of Si nanowires was performed in local electric field by applying of constant negative bias to substrate holder. Deposited Si nanowires were studied by scanning electron microscopy (SEM), Raman and photoluminescence spectroscopy. Correlation between photoluminescence spectra and Si nanowires properties were studied.     

Characterization of ZnS:Cu, Br electroluminescent phosphor prepared by new route

Synthesis of electroluminescent ZnS:Cu, Br phosphor by a number of routes has been presented along with their brightness-voltage, brightness-frequency, brightness-waveform and spectral energy distribution studies. The sample fired in N₂ atmosphere with aluminum and bromine shows predominantly green emission with a peak around 530 nm whereas the sample prepared under H₂S and HBr shows the broadest emission spectrum with multiple peaks. These peaks may arise out of different possible bands of copper, self-activated luminescence of ZnS and association of copper with some of the donor levels formed because of the higher reactivity of HBr. All the samples have been found to obey the relation B=B₀ exp.(−b/V^0.5) which has been discussed using bipolar tunnel emission model. The frequency variation of brightness is linear. Samples containing bromine show multiple secondary peaks indicating that bromine helps in formation of multiple shallow traps.     

The process window for diamond deposition from the vapor phase with sulfur in the C–H–O feed gas mixtures

Theoretical predictions using a modified radical species ternary diagram for C–H–O system indicate that addition of sulfur expands the C–H–O gas phase compositional window for diamond deposition. Sulfur addition to no-growth domain increases the carbon super-saturation by binding the oxygen and the addition of sulfur to the non-diamond domain reduces the heavy carbon super-saturation by decreasing C_nH_m species concentration in the gas phase. The overall effect of sulfur addition to gas phase mixtures is characterized as that of oxygen addition to the C–H system, i.e. expansion of the compositional window over which diamond can be deposited from the gas phase. In addition, the increasing sulfur concentration to diamond domain feed gases beyond 2000 ppm did not affect the steady state gas phase composition but the quality of diamond was reduced.     

COM组件接口方法参数的数据类型的选择

论述了在用 Visual C+ +建造 COM组件时 ,如何选择接口方法参数的数据类型的问题。结合客户程序是 ASP应用程序的情景 ,讨论利用 Visual C+ +和 ATL ,如何在组件程序的一端选择相应的数据类型。