在线multicast数据传输网络中的一个优化问题

首先建立了数据传输网络选择的最小成本模型，给出了有效支撑树代表集的概念，并给出了一个时间复杂性为D(mlogen)的算法产生代表集。然后对静态数据传输问题和在线数据传输问题，分别给出了一个时间复杂性为D(mlogen)和O(m^2 mlogen)的多项式时间的算法。     

脉冲式半导体激光器准直光学系统的设计

根据具体的探测环境和探测精度,通过理论分析,提出了脉冲式半导体激光器准直光束的单透镜设计方法和柱面透镜的设计方法,并且给出了具体的设计参数。可以获得高斯光束的准直发散角为1.48mrad;高斯光束的腰粗为0.325mm。     

一种微透镜阵列的研制

介绍一种利用表面张力的作用、以光纤作材料、用分离的自聚焦透镜制作微透镜阵型的方法，这种方法具有制作工艺简单、无须昂贵设备等优点，用此方法实际制作了具有良好连续面型的微透镜阵列，并对制作的微透镜阵列进行了测试，效果较好。     

水溶液全循环法尿素装置中压分解"三种工艺"的比较

以生产数据结合理论计算的方法系统地比较、分析了水溶液全循环法尿素装置中中压分解“三种工艺”的热能利用、甲铵分解率、总氨蒸出率、水平衡量、一分加热器生产能力等方面的情况，提出应用和配置预分离-预蒸馏工艺的方法，评论该工艺在水溶液全循环法中的地位和作用。     

Transport of a surface-applied corrosion inhibitor in cement paste and concrete

Surface-applied corrosion inhibitors are a kind of repair material and usually contain an aminoalcohol and a component forming a salt with the aminoalcohol. According to the manufacturers, this type of inhibitor penetrates very rapidly into concrete; however, the transport mechanisms have not been sufficiently investigated so far. The major part of the study therefore focused on the transport of the ingredients of an inhibitor in cement paste and concrete, which contained an aminoalcohol and a phosphorous compound. It has been shown that the latter forms an insoluble calcium salt in the environment of cement and precipitates quantitatively. It is thus unable to penetrate from the outside into the alkaline concrete zone and cannot develop its inhibiting effect there. The aminoalcohol, on the other hand, is not bound by cement, but remains largely dissolved in the pore liquid, thus providing optimal conditions for high mobility. The analysis of the transport mechanisms involved has revealed that diffusion in the dissolved state is by far the most efficient transport mechanism. While basically the transport of the aminoalcohol via the gaseous phase is possible, it does play an inferior role only. Surprisingly, the substance had hardly been absorbed by concrete by capillary suction, but at first remained close to the concrete surface.     

合成丁苯嵌段共聚物的影响因素

采用负离子溶液聚合方法制备了丁苯嵌段共聚物，研究了引发剂、活化剂、偶合剂、终止剂对聚合产物性能的影响。     

A three-dimensional FE analysis of large deformations for impact loadings using tetrahedral elements

 A three-dimensional dynamic program for the anaysis of large deformations in contact-penetration problems is developed using the finite element Lagrangian method with explicit time integration. By incorporating a tetrahedral element, which allows a single-point integration without a special hourglass control scheme, this program can be more effective to the present problem. The position code algorithm is used to search contact surface. Eroding surfaces are also considered. The defense node algorithm was slightly modified for the calculation of contact forces. A study of obliquity effects on metallic plate perforation and ricochet processes in thin plates impacted by a sphere was conducted. It is well simulated that on separation of two parts of the sphere, the portion still within the crater tends to perforate, while the portion in contact with the plate surface ricochets. This deformation pattern is observed in experiments, especially at high obliquities. A long rod that impacts an oblique steel plate at high impact velocity was also simulated in order to study the dynamics of the rod caused by the three dimensional asymmetric contact. The agreement between simulated and experimental results is quite good. Fracture phenomena occuring at high obliquity deserves further investigations. Received: 20 February 2002 / Accepted: 20 September 2002     

ㄇ形梁剪力滞效应的解析解

精确分析ㄇ形梁在纵横向荷载共同作用下,其横断面上正应力分布规律对于计算其有效宽度有重要意义,应用力法原理,先将ㄇ形梁和翼板截开成矩形截面梁和平面应力板,在截面上代之以赘余的分布剪力,对于平面应力板,通过利用板变形的对称性来简化其边界条件,然后假设一个满足板的控制方程的Airy应力函数求得板的应力和位移,再利用Timoshenko梁理论求得梁的挠度和转角,根据截面上梁与板的纵向位移相等的变形协调条件便可最终确定截面上的分布剪力,给出的数值算例验证了方法的有效性,并与铜陵长江公路大桥主梁的模型有限元结果和试验结果作了对比,解析解法还可用来检验其他各种数值计算方法的精度,并可推广到其他多跨薄壁结构梁桥的膜应力分析中。     

镍铬合金在酸性CuCl2溶液中反应机理

对铜在酸性CuCl_2溶液中蚀刻反应机理论述,利用氧化-还原电动势原理,详细论述了Ni80Cr20合金在酸性CuCl_2溶液中化学蚀刻反应机理,以及影响蚀刻速度的因素,并对溶液中金属离子的存在形式作了验证。     

饼干炉湿度控制的改进方法

在大空间的温度控制系统中 ,采用简单的PID控制规律 ,对空间的温度、湿度进行解藕计算 ,将空间的相对湿度控制转化为送风含湿量的控制。该控制方式稳定、可靠 ,并且节约能源。本方法适用于所有的烘烤炉中