Magnetic Properties of Fe-Doped Rutile

Ball-milling method was applied to dissolve Fe into titanium dioxide (TiO₂). X-ray diffraction indicated the starting anatase changed to a rutile-type structure with oxygen deficiency after ball milling. Transmission electron microscopy and X-ray absorption experiments were conducted to examine the possible existence of magnetic impurities in the ball-milled powders after they were leached in HCl solutions. Temperature dependence of the resistivity shows semiconducting behavior and the magnetic hysteresis loops at 5 and 300 K exhibit ferromagnetic characteristics. Fe-doped TiO₂ films were also prepared by pulsed laser deposition. The magnetic properties of the films are discussed.     

CeO2对RuO2／γ-A12O3催化剂湿式氧化降解苯酚性能的影响

采用浸渍法制备了RuO2／γ-A12O3和RuO2／CeO2／γ-A12O3催化剂，并利用XRD、SEM和XPS对催化剂进行了表征，研究了Ce的加入对RuO2／γ-A12O3催化剂表面分散性和催化剂表面元素Ru，O和Ce化学态的影响，同时考察了RuO2／γ-A12O3和RuO2／CeO2／γ-A12O3催化剂湿式氧化降解苯酚的活性，并深入探讨了Ce对RuO2／γ-A12O3催化剂的助催化作用。结果表明：Ce掺杂改性后，使催化剂表面Ru的化学态降低、表面氧空位增加，并且活性组分Ru的分散性增加，从而使RuO2／CeO2／γ-A12O3催化剂的活性提高，因此Ce起到了显著的助催化作用。     

Microstructure-Property Correlation in AI_4C_3 Dispersion Strengthened Al Composite

The microstructure and tensile properties of Al_4C_3 dispersion strengthened Al composite fabricatedby reaction milling technique were investigated.It is indicated that the rod-like Al_4C_3 dispersoidshaving a diameter of 0.02-0.03 μm and a length of 0.1-0.3μm are formed by reaction of C with Al,and uniformly distributed in the Al matrix.The interface between Al_4C_3 and Al is clean and theinterfacial bonding is good.The matrix consists of the subgrains which have the size of 0.3-0.4μm,and most of the Al_4C_3 dispersoids are distributed on the subgrain boundaries.The 11 vol.-%Al_4C_3/Al composite exhibits an UTS (ultimate tensile strength) of 400 MPa and anelongation-to-failure of 8.0%.     

A novel way to treat refractory waste: Sonication followed by wet oxidation (SONIWO)

The effectiveness of the hybrid system sonication followed by wet oxidation (SONIWO) to treat otherwise refractory waste has been demonstrated. In such a hybrid system homogeneous CuSO₄ catalyst was found to be very efficient.     

济钢转炉煤气储存加压系统存在缺陷及处理措施

济钢燃气厂针对济钢转炉煤气储存加压系统的设备现状，组织了一次设备大修，大修后煤气柜升降速度提高到了1．0m/min，并解决了加压机前负压等问题。     

Physicochemical and Functional Properties of Freeze-Dried and Oven Dried Corn Gluten Meals

The physicochemical and functional properties of convection oven- and freeze-dried gluten meals of two corn varieties were evaluated. The physicochemical properties (water solubility index, water absorption index, Hunter color parameters, and bulk density) and functional properties (water absorption, oil absorption, least gelation concentration, protein solubility, and emulsification properties) of convection-oven and freeze-dried corn gluten meals were compared with each other and soy flour. Freeze-dried corn gluten meals was observed to have lower bulk density (0.244-0.263 kg/m³) and was lighter in color (high L and ΔE) compared to their counterpart convection oven-dried gluten meals. Freeze-dried gluten meals from both corn varieties showed significantly higher oil absorption, water absorption, pH, emulsification, and protein solubility compared to oven-dried corn gluten meals. The gluten meals from both corn varieties had lower water absorption and bulk density but higher oil absorption than soy flour, suggesting the hydrophobic nature of corn proteins. Corn gluten meals formed thin (pourable) emulsions compared to soy flour emulsions, which were thick salad dressing type. Freeze- and convection oven-dried corn gluten meals showed significantly lower protein solubility measured at different pH than soy flour.     

蓝湿皮酶软化的特性研究

以自行研制的一种复合酶为软化剂 ,研究了 p H值、反应温度、反应时间、酶用量以及铬含量对猪蓝湿皮软化效果的影响 ,其软化效果以软化液中羟脯氨酸的浓度增量来表征。研究结果表明 :通过蓝湿皮软化来改善成品革的质量是可行的 ,而且有明显的效果 ;以软化液中羟脯氨酸的浓度来表征软化效果是一个有效的方法 ;当用该复合酶软化猪蓝湿皮时 ,最适 p H值范围为 6 .0 - 6 .5 ;反应温度在 4 0 - 6 5℃之间时 ,软化效果随温度的升高而增大 ;在 5 5℃条件下 ,该酶有很好的热稳定性 ,能长时间保持活力不衰减 ;最适酶用量为 30 0 U/ g试样 ;蓝湿皮的铬含量对软化效果有影响 ,用该方法处理的蓝湿皮 ,其铬离子质量含量一般应≤ 2 .5 %。     

SHS of shape memory CuZnAl alloys

Aiming at preparation of shape memory alloys (SMAs), we explored the SHS of Cu_{1 − x} Zn_{1 − y} Al_{1 − z} alloys (0.29 < x < 0.30, 0.74 < y < 0.75, and 0.83 < z < 0.96). The most pronounced shape memory effect was exhibited by the alloys of the following compositions (wt %): (1) Cu(70.6)Zn(25.4)Al(4.0), (2) Cu(70.1)Zn(25.9)Al(4.0), and (3) Cu(69.9)Zn(26.1)Al(4.0). The effect of process parameters on the synthesis of CuZnAl alloys was studied by XRD, optical microscopy, and scanning electron microscopy (SEM). The grain size of CuZnAl was found to depend on the relative amount of the primary CuZn and AlZn phases. Changes in the transformation temperature and heat of transformation are discussed in terms of ignition intensity and compaction. Mechanism of the process depends on the level of the temperature attained relative to the melting point of components. At the melting point of AlZn, the process is controlled by the solid-state diffusion of AlZn into a product layer. The ignition temperature for this system depends on the temperature of the austenite-martensite transformation in CuZnAl alloys. The composition and structure of the products was found to markedly depend on process parameters. The SHS technique has been successfully used to prepare a variety of SMAs.      

Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

Triple tangent flank milling of ruled surfaces

This paper presents a positioning strategy for flank milling ruled surfaces. It is a modification of a positioning method developed by Bedi et al. [Comput Aided Des 35 (2003) 293]. A cylindrical cutting tool is initially positioned tangential to the two boundary curves on a ruled surface. Optimization is used to move these tangential points to different curves on the ruled surface to reduce the error. A second optimization step is used to additionally make the tool tangent to a rule line, further reducing the error and resulting in a tool position, where the tool is positioned tangential to two guiding rails and one rule line. The resulting surface has 88% less under cutting than the method of Bedi et al.