六通道瞬态光学高温计

六通道瞬态光学高温计是在可见光和近红外光谱范围内 ,把光源的热辐射取出六个波段进行测量。每个波段信号通过各自的光纤传输、光电倍增管探测和记录仪器记录。系统的时间分辨率小于 30 ns,冲击温度测量范围为 2 30 0～ 90 0 0 K,测量误差小于 5 % ,给出了以碘化钠、硝基甲烷和空气为样品的若干实验结果     

组合式光纤流量传感器

提出了一种新型的组合式光纤流量传感器，介绍了它的工作原理，详细讨论了光脉冲转换器的设计要点，据此设计了传感头，并给出了它的实验结果。     

The effect of fibre alignment on composite strength: II. The strength of angle-ply laminates

Experiments have been carried out on relatively wide angle-ply laminate samples with very short gauge lengths. These proved to be very much stronger than samples tested in earlier work, and which form the basis for our present design with these materials. It is highly likely that the early results for strength were more indicative of edge effects than true laminate strength. This is confirmed by data from tests on pressurized tubes. A review of the literature on this shows that such tests produced results which can be an order of magnitude higher than the early laminate tests. Thus our design calculations could well be severely underestimating the potential strength of angle-ply laminates. This may be having serious consequences for the aerospace industry, through the use of design criteria for strength which may be too conservative. Single-fibre experiments may pave the way for more realistic estimates of angle-ply laminate strengths. These indicate that a simple one-third power rule can be used to estimate the potential strength. However, this is purely ad hoc at present, and needs to be put on a firmer footing through both theoretical and experimental studies. Furthermore, if this approach is adopted, edge effects will still have to be allowed for, and estimated on the basis of the aspect ratio of the part.     

Interaction between bubbles and fibre optic probes in a bubble column

Spherical bulb fibre optic probes, developed and applied for bubble characterization in a bubble column and a slurry bubble column at high temperature, were investigated. The principle of operation of these new optical fibre probes is based on the difference in refractive indices between the gas and the liquid phases. The interaction between the gas bubbles and the fibre optic probes in a bubble column was studied using photographic techniques. The first objective of these experiments was to study the response of the sensors upon contact with gas bubbles of various sizes. The second objective of this study was to establish, under controlled situations, the optical probe bubble detection performance and ability for local quantitative measurements of the bubble rise velocity and the gas hold-up.     

靛蓝染料废水的处理研究

采用膜技术和絮凝方法处理牛仔布印染过程中的生产废水。对经处理后的水色度和COD的去除进行了比较。膜法处理后的水要优于絮凝处理后的水，可回用于生产。     

Dietary fibre of coconuts from a pacific atoll: Soluble and insoluble components in relation to maturity

Polysaccharide fractions were measured in coconuts at three stages of maturity, which corresponded to dietary usage in the Tokelau Islands of the South Pacific. Kernel was sequentially extracted with cold water (CW), hot water (HW) hot 0.5% ammonium oxalate (HOX), 1M H² SO⁴ and 72% H² SO⁴, and the monosaccharide compositions of the fractions determined. Total readily soluble fractions (CW+HW+HOX) were predominantly galactomannan, and decreased from 77% of the polysaccharide in the immature kernel to 8.8% of that in the mature kernel. Insoluble mannan increased during maturation to be the major polysaccharide component in mature kernel. This indicates that marked differences exist between the three stages of maturity examined, in the properties of their dietary fibre. The results suggest that in studies of diets in which coconut is a staple part, there is a need for careful definition of the coconut component with respect to maturity. Furthermore, they show the importance of using dietary fibre methods which are appropriate to the solubility characteristics of the indigestible polysaccharide.     

耐火纤维喷涂辅助技术

文章主要论述了耐火纤维喷涂炉衬的特点及性能，以及对辅助工艺的要求，并对耐纤喷涂炉衬和纤维喷涂针刺炉衬进行了试验对比，说明耐火纤维喷涂技术前景广阔。     

Comparison of interfaces in Ti composites reinforced with uncoated and TiB2/C-coated SiC fibres

Interfaces play an important role in determining the mechanical properties of composite materials. The interfaces established between a titanium-alloy matrix (Ti-6Al-4V) and uncoated and TiB₂/C-coated SiC fibres are analysed by scanning electron microscopy, transmission electron microscopy and X-ray techniques. Emphasis is placed upon the interfacial morphology and microstructure, identification of reaction products, and the stability of the coating layer. Complex multi-reaction layers are observed frequently in the interfacial zones. Previous, often contradictory, reports about the interlayers are reviewed. Experimental observation demonstrates that the type and distribution of interlayers vary in a given system, due to prolonged treatment of the samples at temperature. The formation and distribution of the interlayers are discussed further, with respect to these and previous findings. Methods of reducing interfacial reactivity are discussed.