Preparation of branched polyacrylonitrile through self‐condensing vinyl copolymerization

Branched polyacrylonitrile (PAN) was prepared through a self‐condensing vinyl copolymerization of acrylonitrile and 2‐(2‐bromopropionyloxy)ethyl acrylate (BPEA). The branched architecture of the product was confirmed by NMR spectra and the average degree of branching (DB ) was estimated. Through a comparison of the intrinsic viscosity of the product with that of its linear analogue, the contraction factor g′ was calculated. It was found that the viscosity of the branched PAN was obviously lower that that of linear PAN. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Non-invasive headspace measurement for characterizing oxygen-scavenging in polymers

A non-invasive headspace analysis method to measure rate and amount of oxygen uptake in oxygen-scavenging polymers is presented. Oxygen uptake data for metal-catalyzed poly(1,4-butadiene) at 30 °C are provided to illustrate the method. These data were obtained by measuring oxygen headspace concentration above the scavenging polymer with an OxySense^® 200T non-invasive oxygen sensor, and, for comparison, oxygen uptake was measured with an analytical balance. Excellent agreement was observed between these two independent experiments.     

Simulation of Facial Muscle Actions Based on Rational Free Form Deformations

This paper describes interactive facilities for simulating abstract muscle actions using Rational Free Form Deformations (RFFD). The particular muscle action is simulated as the displacement of the control points of the control-unit for an RFFD defined on a region of interest. One or several simulated muscle actions constitute a Minimum Perceptible Action (MPA), which is defined as the atomic action unit, similar to Action Unit (AU) of the Facial Action Coding System (FACS), to build an expression.     

Free convection and mass transfer flow of non-newtonian fluid with thermal diffusion effect

An analytical study is performed to examine the thermal diffusion characteristics of free convection and mass transfer flow in a non-Newtonian fluid (Walters, 1962: liquid B') past a uniformly accelerated infinite vertical plate in the presence of thermal diffusion. The expression for the velocity field is obtained by the Laplace transform technique. The influence of the Soret number (a thermal diffusion parameter) on the velocity field is extensively discussed with the help of graphs.     

催化氧化法合成脂肪醇醚羧酸盐的研究进展

详细介绍了氮氧自由基催化氧化法和贵金属催化氧化法合成脂肪醇醚羧酸盐。氮氧自由基催化时,反应温度20～60℃,反应时间3～6 h,得到酸型产品。贵金属催化剂中,钯的催化活性比铂高。贵金属催化时,加入铅、铋等助催化剂,并以活性炭为载体,碱性条件下于50～90℃反应2～6 h,得到盐型产品。在适当的条件下,这两种方法均可使醇醚转化率达95％,选择性达90％以上。     

Evaluation of different coating systems by electrochemical methods

Corrosion protection of organic coated steel is determined by free corrosion potential measurements and impedance spectroscopy. The results are classified by means of very basic considerations and evaluation figures are developed. These electrochemical data are correlated with the extent of the corrosion for each coating system. The evaluation figures are used for ranking coating systems and this ranking is correlated with the ranking with reference to the results of standardized and exposure tests.     

Preparation of Iron Filler-Based Photocomposites and Application in 3D Printing

The introduction of metallic fillers to polymers via the photopolymerization approach can endow the composite materials with some unique properties, but the relevant research is still scarce due to the issue of light penetration and inner filter effect. Herein, for the first time the fabrication of photocomposites based on fine iron powder (i.e., a typical kind of metallic filler) is reported in this work. The free radical polymerization of two different acrylate monomers, poly(ethylene glycol) diacrylate and trimethylolpropane triacrylate, is performed in the presence of iron filler under mild conditions (i.e., light emitting diode (LED)@405 nm irradiation at room temperature under air). And the real-time Fourier transform infrared spectroscopy reveals remarkable photopolymerization kinetics of acrylates with high final conversions and fast polymerization rates despite the increasing contents of iron filler in the composites. Interestingly, the 3D printing technique is applied to the iron filler-based composites to produce tridimensional patterns with excellent spatial resolution. This work not only paves the way for the investigation of photocomposites based on metallic fillers through photochemical methods, but also broadens the potential application prospects.     

工艺参数对射频磁控溅射PTFE靶形成的等离子体组成的影响

采用四极质谱仪测量了试验参数对高压脉冲增强射频磁控溅射PTFE靶等离子体气氛的影响规律。结果表明：增加脉冲偏压、脉冲频率、脉宽、射频功率和气压能提高Az离子对PTFE靶的溅射能力，增加空间中氟碳自由基的数量，其中各参数对峰位位于25．0aum处的氟碳自由基强度影响最大：脉冲电压从10kV提高到20kV能将该峰强度提高2倍；脉宽从40s提高到100μs强度提高80倍；频率从50Hz提高到200Hz强度提高4倍；溅射气压由0．1Pa提高到0.3Pa强度提高6倍；射频功率由200W提高到400W强度提高6倍。励磁电流能有效的约束氟碳自由基的空间分布。     

Properties of poly(n‐butyl methacrylate) prepared by reverse atom transfer radical polymerization in an aqueous dispersed system

Reverse atom transfer radical polymerization (ATRP) of n‐butyl methacrylate (BMA) in waterborne media using Cu(II) complexes with azo initiators (i.e., reverse ATRP) was conducted. The influence of several factors, such as surfactant, catalyst, and reaction time, on the stability of the emulsion, the particle size, the morphology of the emulsion particles, and the control of the polymerization was investigated. The results showed great differences between ATRP and conventional emulsion polymerization, especially the nucleation mechanism and the kinetics. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1542–1547, 2003     

无油迷宫式压缩机在含尘气体中的应用与改进

针对迷宫式压缩机在含尘气体中使用所出现的使用周期短等问题 ,在压缩机进口增设水洗塔、丝网除沫器 ,并对压缩机气阀、气缸盖等相关部件进行改进 ,取得了较好的效果