防水粉憎水膜形成机理及稳定性的研究

通过对防水粉憎水膜形成途径的探索，提出了憎水膜形成过程的基本假设，利用微观测试方法证实了憎水膜层的存在．试验并研究了防水粉长期稳定性的诸多问题。     

IR spectroscopic study of Pt/Kl zeolites using adsorption of CO as a molecular probe

FTIR spectra of CO adsorbed on Pt/KL catalysts show that the relative band intensities and the total dispersion markedly depend on the catalyst preparation method (ion exchange, incipient wetness impregnation or co-impregnation with KCl). The CO stretching frequency of the dominant band for linear CO is shifted to higher wavenumbers, parallel with the proton concentration in the reduced catalyst, which is derived independently from the intensity of the IR bands of the OH groups. The results are in accordance with the model that electron-deficient platinum particles are platinum-proton adducts.On leave from: N.D. Zelinsky Institute of Organic Chemistry, Academy of Sciences, Moscow, USSR.     

Effect of Lateral Cracks on Fracture Toughness Determined by the Surface-Crack-in-Flexure Method

The surface-crack-in-flexure (SCF) method uses a Knoop indenter to create small, semielliptical surface precracks in beam specimens. Lateral cracks may interfere with the primary median crack and cause errors of up to 10% in determination of fracture toughness, particularly for materials for which the fracture toughness is ∼3 MPa·m^1/2 or less. Although the residual-stress-damage zone is ground or polished away by hand by removing 4.5–5 times the indentation depth, this amount may not be sufficient to completely remove the lateral cracks in low-fracture-toughness materials. A series of tests were conducted on sintered alpha silicon carbide with different amounts of material removed after indentation. Once the lateral cracks were fully removed, the SCF results concurred with single-edged-precracked-beam and chevron-notched-beam data collected in accordance with ASTM Designation C1421. A simple remedy for the SCF method is to examine the outer ground surface for remnants of lateral cracks before fracture and to remove more material if necessary.     

DX centers in AlxGa1-xAs bulk alloy,AlAs/GaAs ordered,and disordered superlattices

Properties of theDX centers in Al_0.5Ga_0.5As bulk alloy (b-AL), (AlAs)₂ (GaSa)₂ ordered superlattice (o-SL) and (AlAs) _m (GaAs) _n disordered superlattice (d-SL) (m = 1, 2, 3,n = 1, 2, 3) with the same macroscopic composition were measured and compared. By deconvolution of deep level transient spectroscopy (DLTS) spectrum due to theDX center, we have found a decrease in the number of separate peaks in DLTS spectrum in an intentionally atomic ordered arrangement. Visiting Scholar of the Japan Society for the Promotion of Science. On leave from Department of Electrical Engineering, San Jose State University, San Jose, California 95192-0084, USA.     

分离有机/有机混合物的PVA、CA系列膜及其渗透汽化性能研究(Ⅱ) 成膜条件对渗透汽化性能的影响

用溶剂完全蒸发法制备了PVA复合膜 .经对MTBE/MeOH混合物的分离实验得到了PVA复合膜的最佳成膜条件 ,即 :铸膜液中PVA、马来酸浓度分别为 7%、3% ,热处理温度130～ 15 0℃ .在 1%～ 2 %丙酮水溶液中浸泡处理 4～ 8h ,CTA中空纤维RO膜被改性成渗透汽化膜 .CTA中空纤维膜的分离性能优于其它醋酸纤维素系列膜 ,PVA/CA复合膜的性能优于PVA/PAN复合膜和CA/PAN复合膜     

基于校园网的计算机考试系统的设计与实现

通过对计算机考试系统现状的分析,从技术发展和考试改革的需要入手,介绍了一种面向应用,基于校园网,以B/S结构模式为主,以C/S结构模式为辅,可实现远程题库维护的一体化计算机考试系统的基本构成和功能,并提供了相应的设计思路和关键技术的实现方法。     

Flexible microelectronics becoming a reality with Suftla transfer technology

Abstract— Suftla is a technology that is used to transfer polycrystalline silicon (polysilicon) thin‐film‐transistor (TFT) circuits from an original glass substrate to a plastic sheet. The electronic devices in the next generation will be thin, lightweight, and will handle huge amounts of data, yet consume less energy. Suftla technology, together with high‐performance polysilicon TFTs, meets all these requirements because we have developed a variety of smart flexible electronic devices, such as thin paperback‐sized displays and microprocessors. Suftla will usher in a new era of life‐enhancing flexible microelectronics.     

Neural Networks Analysis of Steel Plate Processing Augmented by Multi‐objective Genetic Algorithms

An earlier neural network analysis of processing of steel plates through hot rolling was subjected to a further refined analysis through some flexible neural networks that evolved using a multi‐objective predator‐prey genetic algorithm. The original data set expressing the Yield Strength and Ultimate Tensile Strength of the rolled slabs in terms of a total of 108 process variables were subjected to a systematic pruning through this evolutionary approach, till the nitrogen content of the steel emerged as the most significant input variable. A theoretical explanation is provided for this slightly unexpected result.     

Engset multi‐rate state‐dependent loss models with QoS guarantee

We consider a single link loss system of quasi‐random input, described by the Engset multirate loss model (EnMLM). Blocked calls may once reattempt to be connected to the system requiring less bandwidth; then the system is described by the single retry model for finite sources (f‐SRM). The EnMLM and the f‐SRM are extended with the single threshold finite source model (f‐STM), where calls may attempt to be connected to the system with less bandwidth requirements, according to the link occupancy, before blocking occurs. We focus on CBP equalization in the EnMLM, f‐SRM and f‐STM, under the bandwidth reservation (BR) policy. For this analysis, we apply two approximate methods, the Roberts' method and the method of reverse transition rates (RTR), which lead to a recursive CBP calculation. We evaluate the accuracy of the above models under the BR policy by comparing the analytical with simulation CBP results, based on the relative approximation errors (RAE). The results are highly satisfactory because they show that the proposed models (formulas) lead to small RAE. Copyright © 2005 John Wiley & Sons, Ltd.