Air Filtration and Radon Decay Product Mitigation

Air cleaning as a means of mitigating the risks arising from exposure to indoor radon progeny has been evaluated in a single-family house in the north eastem US. using an automated, semi-continuous activity-weighted size distribution measurement system. The measurements included radon concentration, condensation nuclei count, and activity-weighted size distribution of radon decay products. Measurements were made in the house with and without an operating air filtration system and with various particle sources common to normal indoor activities operating. Aerosols were generated by running water in a shower, candle burning, cigarette smoking, vacuuming, opening doors, and cooking. Using a room model, the changes in attachment rates, average attachment diameters, and deposition rates of the unattached fraction with and without the air cleaning system were calculated. In the presence of active aerosol sources, the air filtration unit typically reduced the concentration of particles within the hour following the end of particle generation. After candle burning, cigarette smoking, and vacuuming in the bedroom, the reductions of PAEC by air filtration are about 60% with the air filtration system operating in the bedroom. During cooking in the kitchen, the reductions of PAEC in the bedroom with the air filtration system were about 40%. However, for all cases the dose reductions were smaller than the particle and PAEC reductions. For those particles that were generated within the bedroom, there was a 20% to 50% reduction in dose. In the case of cooking where the door was open and particles infiltrated from the rest of the house, the dose reduction was only 5% on average and appears to be insignificant. Thus, the dose reductions were h e r than the reductions in activity concentration, but there were no cases where the estimated dose actually increased.     

Novel miniature integrated optical goniometers

A new principle and arrangement for directly determining the angle of incidence of an optical beam on an object are proposed and demonstrated. The novelty of the approach lies in the realization of a ‘smart object’, which extracts a portion of the incident beam's power into an optical waveguide attached to the object's surface or embedded in its body for converting the angle of incidence into the position of a guided beam with finite lateral extent. This ‘integrated optical light pointer’ beam is accomplished by means of creating additional degrees of freedom on the target in two different ways. While a first type is based on introducing spatial variations of the waveguide thickness, a second type makes use of a chirp of the grating periodicity. The feasibility for practical applications has been experimentally demonstrated by a direct comparison with a commercial high-resolution encoder, resulting in an r.m.s. error of <30′'. Measurements have been performed for chips fabricated based on replicated polycarbonate substrates and with no external optics, showing the great potential of this approach for realizing low-cost yet high-performance miniature goniometers.     

不锈钢绕带容器环板与绕带端头的焊接

本文通过焊接试验对奥氏体不锈钢绕带容器环板与绕带焊接工艺进行了研究分析,并得出了合理的焊接方法和工艺参数。     

采取具体措施 发挥教研室的职能作用

本文就如何发挥高校教研室的职能作用记述了本教研室所采取的具体方法和措施。     

Combined shape and sizing optimization of truss structures

 In this paper, an evolutionary optimization method is presented for weight minimum problem of a 3-dimensional truss structure in terms of nodal coordinates and element cross-sectional areas. The structure is subject to stress, local buckling and displacement constraints. Two types of design variables with different natures are optimized separately: (1) a fully stressed design (FSD) and scaling techniques are applied to sizing variables and (2) the evolutionary node shift method is applied to shape variables. Alternating procedure is utilized to couple the two types of variables and to combine the results. The optimum solution is achieved gradually from the initial configuration design. Two typical truss structures are examined to illustrate the validity of the method. Received: 22 October 2001 / Accepted: 04 June 2002 This research work is supported by the National Natural Science Foundation of China under the guarantees no. 10072050 and 10172072, respectively.     

Discrete Modeling and Suggested Measurement of Heat Transfer in Gas-Solids Flows

This article presents a two-dimensional transient model for gas-solids flow and heat transfer through pipes using the coupled Computational Fluid Dynamics and Discrete Element Method approach. Numerical simulations have been conducted to examine the modification of fluid thermal structure due to the presence of particles in a pneumatic transport pipeline. Modeled results have demonstrated the key role of transversal motion of rebounding particles in the pipe cross section in altering fluid temperature. Further implementation of this modeling technique in air-drying processes is discussed and possible experimental methods for the measurement of in situ particle and fluid motion and temperature profile are cited.     

The thermal ignition of lignocellulosics in infinite slab and cubic geometries

Wood shaving samples were heated in both cubic baskets and in a previously described system realising the conditions of the ‘infinite slab’ in thermal ignition. Results from the two sets of experiment were found to be totally consistent with each other.