组合式光纤流量传感器

提出了一种新型的组合式光纤流量传感器，介绍了它的工作原理，详细讨论了光脉冲转换器的设计要点，据此设计了传感头，并给出了它的实验结果。     

The effect of fibre alignment on composite strength: II. The strength of angle-ply laminates

Experiments have been carried out on relatively wide angle-ply laminate samples with very short gauge lengths. These proved to be very much stronger than samples tested in earlier work, and which form the basis for our present design with these materials. It is highly likely that the early results for strength were more indicative of edge effects than true laminate strength. This is confirmed by data from tests on pressurized tubes. A review of the literature on this shows that such tests produced results which can be an order of magnitude higher than the early laminate tests. Thus our design calculations could well be severely underestimating the potential strength of angle-ply laminates. This may be having serious consequences for the aerospace industry, through the use of design criteria for strength which may be too conservative. Single-fibre experiments may pave the way for more realistic estimates of angle-ply laminate strengths. These indicate that a simple one-third power rule can be used to estimate the potential strength. However, this is purely ad hoc at present, and needs to be put on a firmer footing through both theoretical and experimental studies. Furthermore, if this approach is adopted, edge effects will still have to be allowed for, and estimated on the basis of the aspect ratio of the part.     

Interaction between bubbles and fibre optic probes in a bubble column

Spherical bulb fibre optic probes, developed and applied for bubble characterization in a bubble column and a slurry bubble column at high temperature, were investigated. The principle of operation of these new optical fibre probes is based on the difference in refractive indices between the gas and the liquid phases. The interaction between the gas bubbles and the fibre optic probes in a bubble column was studied using photographic techniques. The first objective of these experiments was to study the response of the sensors upon contact with gas bubbles of various sizes. The second objective of this study was to establish, under controlled situations, the optical probe bubble detection performance and ability for local quantitative measurements of the bubble rise velocity and the gas hold-up.     

Dietary fibre of coconuts from a pacific atoll: Soluble and insoluble components in relation to maturity

Polysaccharide fractions were measured in coconuts at three stages of maturity, which corresponded to dietary usage in the Tokelau Islands of the South Pacific. Kernel was sequentially extracted with cold water (CW), hot water (HW) hot 0.5% ammonium oxalate (HOX), 1M H² SO⁴ and 72% H² SO⁴, and the monosaccharide compositions of the fractions determined. Total readily soluble fractions (CW+HW+HOX) were predominantly galactomannan, and decreased from 77% of the polysaccharide in the immature kernel to 8.8% of that in the mature kernel. Insoluble mannan increased during maturation to be the major polysaccharide component in mature kernel. This indicates that marked differences exist between the three stages of maturity examined, in the properties of their dietary fibre. The results suggest that in studies of diets in which coconut is a staple part, there is a need for careful definition of the coconut component with respect to maturity. Furthermore, they show the importance of using dietary fibre methods which are appropriate to the solubility characteristics of the indigestible polysaccharide.     

Comparison of interfaces in Ti composites reinforced with uncoated and TiB2/C-coated SiC fibres

Interfaces play an important role in determining the mechanical properties of composite materials. The interfaces established between a titanium-alloy matrix (Ti-6Al-4V) and uncoated and TiB₂/C-coated SiC fibres are analysed by scanning electron microscopy, transmission electron microscopy and X-ray techniques. Emphasis is placed upon the interfacial morphology and microstructure, identification of reaction products, and the stability of the coating layer. Complex multi-reaction layers are observed frequently in the interfacial zones. Previous, often contradictory, reports about the interlayers are reviewed. Experimental observation demonstrates that the type and distribution of interlayers vary in a given system, due to prolonged treatment of the samples at temperature. The formation and distribution of the interlayers are discussed further, with respect to these and previous findings. Methods of reducing interfacial reactivity are discussed.     

玻璃钢制品拉拔模具的型腔表面处理工艺

玻璃钢制品拉拔工艺是较为先进的制造工艺之一，拉拔模具是决定玻璃钢制品质量好坏的关键。介绍了玻璃钢制品拉拔模具的型腔表面处理工艺，采用该处理工艺能有效地提高玻璃钢制品的质量。     

延缓与加速A1-Cu合金时效析出反应的研究

研究了溶质原子浓度、Si晶体第二相、残余形变、外加莫来石(Mullite)短纤维及其交互作用，对二元Al—Cu合金时效析出行为的影响。试验材料采用挤压铸造方法制备，复合材料中纤维体积分数为18％。实验结果表明：随溶质原子浓度的升高，A1-Cu二元合金中GP，θ″和θ′相的析出都得到了相应加快；Si含量超过一定值后，随Si含量增加，A1-Cu-Si合金中GP区形成受到抑制，而θ″和θ′相的析出得到加快；形变对GP区的抑制和对θ″，θ′和θ相的加速析出具有十分明显的作用；纤维本身除对GP区抑制和对θ″，θ′相的析出加速外，还会与溶质原子、合金元素或第二相以及残余形变交互作用，使GP区被抑制，而θ″，θ′甚至θ相被加速析出等现象进一步加强。用位错理论能较好地解释析出反应延缓与加速的微观机理。     

高岭土改性聚酯纤维

介绍了高岭土在改性聚酯中的作用、纤维级高岭土的性质以及改性聚酯的制造方法．指出了我国开发高岭土改性聚酯纤维的的前景．