GaAs Mach－Zehnder型光波导开关／调制器

采用非对称Ｘ结耦合器代替传统的Ｙ分支器，研制了ＧａＡｓＭａｃｈ－Ｚｅｈｎｄｅｒ型２×２光开光，得到了小于－２２．４ｄＢ的串音比和１２Ｖ左右的开关电压，器件的波导传输损耗小于７ｄＢ／ｃｍ。预计该器件可广泛应用于ＧａＡｓ开关列阵及高速光调制等领域。     

Cr12钢的预处理工艺研究

本文研究了Ｃｒ１２钢经４种不同的预处理工艺处理后钢中碳化物的大小，数量，分布及钢的硬度，强度和韧性，试验结果表明，经调质处理，高温固溶淬火＋高温退火处理后，Ｃｒ１２钢中碳化物的大小，分布及其组织，性能均优于常规球化退火预处理的。通过扫描电镜对冲击断口的分析，初步探讨了新的预处理工艺提高韧性的原因。     

Immobilization of inert TRISO-coated fuel in glass for geological disposal

Vitrification of TRISO-coated gas reactor fuel particles was achieved via two methods: glass melting and sintering. Inert TRISO-coated fuel particles and a borosilicate glass were used. With glass melting at 1200-1300 °C floatation and decomposition of carbon and silicon carbide occurred. Thermal pre-treatment of the particles for oxidation of pyrocarbon did not improve the coating properties of the glass. During cooling most of the particles floated and sorbed on the crucible or mold walls. The sintered glass at 700 °C showed better coating properties of the TRISO-coated fuel particles despite higher porosity compared to glass made by melting. Aqueous leaching properties of glass with particles are similar regardless the mode of fabrication, indicating the good chemical durability of the sintered glass. Sintered glasses may constitute a good technique for TRISO-coated fuel particles immobilization for an eventual deep geological disposal.     

CDMA 1X PDSN分组数据网安全性分析及解决方案

首先从CDMA1X网络结构进行详细分析,引出CDMA1X网络安全风险分析。根据网络安全原理,联系江西联通现在CDMA1X网络结构,采取对每层安全进行预防,提出较详细的网络安全解决方案,最后对现网进行安全评估。     

中压变频器在宣钢炼钢厂除尘风机中的应用

本文介绍了SIMOVERT MV中压变频器在宣钢炼钢厂一次除尘风机中的应用情况。变频器现场运行表明，采用中压变频器对转炉除尘风机进行调速节能获得了成功，节能效果明显。     

应用M68HC908LJ12设计单相复费率电能表

介绍了以Motorola公司的M68HC908LJ12高性能单片机为CPU的单相复费率电能表的硬、软件设计和抗干扰设计。     

包钢选矿厂降低铁精矿中氟含量的技术攻关

为了降低铁精矿氟含量,通过采取控制磨矿粒度、改进浮选工艺、采用高效捕收剂等措施,使包钢选矿厂铁精矿氟含量由1999年的0.75%降低到2000年的0.65%、2001年的0.58%,为包钢环保工作目标的完成做出了突出贡献.     

X射线三轴晶衍射法测量半绝缘GaAs单晶的化学配比

采用X射线三轴晶衍射法,根据As间隙原子对作为过量As在GaAs单晶材料中存在的主要形式的模型,可以无损、高精度测量半绝缘GaAs单晶的化学配比.并探讨了引起晶格变化的原因及其与熔体组分的关系,对于制备高质量GaAs单晶及其光电器件具有重要的意义.     

A hybrid extended finite element/level set method for modeling phase transformations

A hybrid numerical method for modelling the evolution of sharp phase interfaces on fixed grids is presented. We focus attention on two‐dimensional solidification problems, where the temperature field evolves according to classical heat conduction in two subdomains separated by a moving freezing front. The enrichment strategies of the eXtended Finite Element Method (X‐FEM) are employed to represent the jump in the temperature gradient that governs the velocity of the phase boundary. A new approach with the X‐FEM is suggested for this class of problems whereby the partition of unity is constructed with C¹(Ω) polynomials and enriched with a C⁰(Ω) function. This approach leads to jumps in temperature gradient occurring only at the phase boundary, and is shown to significantly improve estimates for the front velocity. Temporal derivatives of the temperature field in the vicinity of the phase front are obtained with a projection that employs discontinuous enrichment. In conjunction with a finer finite difference grid, the Level Set method is used to represent the evolution of the phase interface. An iterative procedure is adopted to satisfy the constraints on the temperature field on the phase boundary. The robustness and utility of the method is demonstrated with several benchmark problems of phase transformation. Copyright © 2002 John Wiley & Sons, Ltd.     

基于MSP430F147的网络化通风机监测仪的设计与实现

针对煤矿安全生产中的具体要求,以MSP430高性能单片机为核心,采用网络化通信技术对通风机的电气性能和机械性能进行监测.