Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

哈得4联合站技术改造

位于塔克拉玛干大沙漠腹地的哈得4油田,2004年成为全国最大的沙漠油田,2005年产量达到200×104t。在对联合站存在问题逐一分析的基础上,提出了技术改造的措施。现场采集的运行数据表明技术改造效果明显,增强了流程可靠性,提高了自动化水平,降低了能耗。     

Inhibition effect of carbon dioxide on the oxidation of hydrogen over a platinum foil catalyst

This paper investigates the catalytic ignition of the H₂/O₂/CO₂ mixture on platinum in a stagnation flow at atmospheric pressure experimentally and numerically. We measure the ignition temperatures of the gas mixtures flowing towards resistively heated platinum with various composition ratios and various diluent gases of N₂, Ar and CO₂. Compared with N₂ or Ar, the CO₂ dilution shows higher ignition temperature by about 50 K, even at the same composition ratio. The ignition temperature increase is proportional to the dilution ratio. Through the numerical simulation, it is illustrated that higher ignition temperature is caused by the adsorption of CO₂ and following dissociation on platinum surface, which was to date considered negligible in catalytic combustion.     

凝胶成型法制备加氢催化剂载体的研究与工业化生产

采用凝胶成型法制备加氢催化剂载体，并进行了工业放大试验。通过BET、NH3-TPD、H2-TPR等表征手段及实际的加氢反应性能评价对凝胶成型法制备的载体及加氢催化剂与常规方法进行对比分析，结果表明，采用凝胶成型法所制得的载体及催化剂均具有较高的孔体积和比表面积、较低的堆密度，其机械强度可满足工业要求，总酸量及中强酸酸量得到提升，催化剂活性组分与载体强结合力得到削弱，金属利用率提高，应用性能明显优于传统方法制备的加氢催化剂载体。通过该方法完成了加氢催化剂载体的工业生产，所生产的载体应用于天津院THDS-3加氢精制催化剂取得了良好的工业应用效果。     

校园网宿舍网络管理模式的探讨

讨论了高校学生宿舍区网络的特点，结合天津商学院校园网的实践，讨论了校园网宿舍网络管理的模式。     

Fe3O4/PSt/TiO2多层包覆电磁响应微球的制备

首先采用分散聚合法将自制的Fe3O4磁流体和苯乙烯反应合成有磁核的Fe3O4/PSt磁性聚合物微球，然后，用非均匀成核水解反应在Fe3O4/PSt微球外包覆无定形二氧化钛，获得Fe3O4/PSt/TiO2复合微粒。用红外光谱、扫描电镜和热分析对粒子的形貌和结构进行了表征。并测试了微粒的介电性能和磁性，结果表明，所制得复合微粒有良好的电、磁响应性。     

二氧化锡溅射工艺研究

SnO2 是最早使用也是目前使用最广泛的一种气敏材料 ,使用该材料设计制作的气敏传感器具有许多优点。在简要介绍溅射镀膜的成膜过程和特点的基础上 ,着重介绍了SnO2 膜的制备流程 ,分析了功率和温度变化对成膜质量的影响     

在二(2-乙基己基)磷酸钠的微乳液中金属萃合物对水增溶的影响

测算了由二（2－乙基己基）磷酸钠，金属盐（CoSO4,NiSO4,ZnSO4,MgCl2或Cr(NO3)3)水溶液，正辛醇和正辛烷组成的微乳液中正辛醇从连续油相到界面的ΔGo→i^o和水的极限增容量φ'H2O。用金属萃取络合物反胶束的形成及其亲油性解释了金属离子对φ'H2O和ΔGo→i^o的影响。     

Preparation and properties of nano-sized SnO2 powder

1　INTRODUCTIONSnO2isoneofthemainmaterialsusedingassensor.Becauseofthehumidityandgassensingfunction,itattractsmoreandmoreattentions.Butthepresentproblemishowtoimprovethestabilityandsensibilityofgassensor.Researchershavetakenmanymeasurestoresolvethisproble…     

Dissolved organic carbon dynamics in the upper rhone: The influence of side-arms?

Dissolved organic carbon (DOC) dynamics were investigated over a two year period in the Upper Rhǒne River to examine the role of side-arms in providing DOC to the main channel in relation to discharge fluctuations, especially floods. Concentrations of DOC are shown to remain low in space and in time (average 1.5 mg ^?1) and to be more related to global hydrological events (precipitation) than to any local flushing for backwaters during floods. The results do not support the general assumption that side-arms are the providers of DOC to the main channel.