透反液晶显示器

兼有透射型和反射型液晶显示优点的透反液晶显示可工作于透射和反射两种显示模式，它将广泛应用于手机、PDA等通讯领域。透反液晶显示可分为单盒厚和双盒厚两大类。又可分为扭曲型和非扭曲型两种。为了研制出高性能透反液晶显示器，需解决透反两个显示区的响应时间、光效率、色饱和度的差异以及视角等问题。文中介绍了Sharp公司开发的2种基本的透反液晶显示。以及3种新近开发的高性能透反液晶显示。随着应用市场的扩大和技术的进步，透反液晶显示将会进一步得到发展。     

液晶光阀光电导层光吸收系数的研究

用化学气相沉积法制备了液晶光阀中光电导层———非晶硅薄膜,从实验中得出最佳制备工艺的参数取值。给出了用包络线法测量非晶硅薄膜光吸收系数的原理,测量了样品的光吸收系数随波长的变化规律。得到样品在最佳工艺条件下的光吸收系数高于1×103cm-1。     

Reduced modified quadratures for quadratic membrane finite elements

Reduced integration is frequently used in evaluating the element stiffness matrix of quadratically interpolated finite elements. Typical examples are the serendipity (Q8) and Lagrangian (Q9) membrane finite elements, for which a reduced 2 × 2 Gauss–Legendre integration rule is frequently used, as opposed to full 3 × 3 Gauss–Legendre integration. This ‘softens’ these element, thereby increasing accuracy, albeit at the introduction of spurious zero energy modes on the element level. This is in general not considered problematic for the ‘hourglass’ mode common to Q8 and Q9 elements, since this spurious mode is non‐communicable. The remaining two zero energy modes occurring in the Q9 element are indeed communicable. However, in topology optimization for instance, conditions may arise where the non‐communicable spurious mode associated with the elements becomes activated. To effectively suppress these modes altogether in elements employing quadratic interpolation fields, two modified quadratures are employed herein. For the Q8 and Q9 membrane elements, the respective rules are a five and an eight point rule. As compared to fully integrated elements, the new rules enhance element accuracy due to the introduction of soft, higher‐order deformation modes. A number of standard test problems reveal that element accuracy remains comparable to that of the under‐integrated counterparts. Copyright © 2004 John Wiley & Sons, Ltd.     

膜分离技术在水处理领域的应用

对2000年底巴黎“饮用水和工业用水制造领域中的膜技术”国际会议进行了简单的回顾，根据会议经历对当今膜分离技术在水处理领域的应用市场进行分析，提出今后液体膜分离技术的研究和发展的重点。最后对我国液体分离膜技术的发展提出一些建议。     

Ozonation of CI Reactive Black 5 using rotating packed bed and stirred tank reactor

This study investigates the ozonation of CI Reactive Black 5 (RB5) by using the rotating packed bed (RPB) and completely stirred tank reactor (CSTR) as ozone contactors. The RPB, which provides high gravitational force by adjusting the rotational speed, was employed as a novel ozone contactor. The same ozone dosage was separately introduced into either the RPB or the CSTR for the investigation, while the experimental solution was continuously circulated within the apparatus consisting of the RPB and CSTR. The decolorization and mineralization efficiencies of RB5 in the course of ozonation are compared for these two methods. Moreover, the dissolved and off‐gas ozone concentrations were simultaneously monitored for the further analysis. As a result, the ozone mass transfer rate per unit volume of the RPB was significantly higher because of its higher mass transfer coefficient and gas–liquid concentration driving force. Furthermore, ozonation kinetics was found to be independent of the gravitational magnitude of an ozone gas–liquid contactor. Therefore, the results suggest employing RPBs as ozone‐contacting devices with the advantage of volume reduction. The experimental results, which can be used for further modeling of the ozonation process in the RPB, also show the requirement of correct design for the RPB. Consequently, the present study is useful for the understanding of practical application of RPBs. Copyright © 2004 Society of Chemical Industry     

PVDF中空纤维滤膜的形态结构

用Ｌ－Ｓ相转换法制备了聚偏氟乙烯（ＰＶＤＦ）中空纤维不对称滤膜。铸膜液由聚合物、溶剂和添加剂组成。用电子显微镜（ＳＥＭ）考察了聚合物浓度、添加剂用量及种类对膜形态结构的影响。实验结果表明，聚合物浓度对膜形态结构有显著影响，当铸膜液中聚合物浓度较低时，无论用什么种类添加剂，都能形成大、且多的孔，但孔的形状随添加剂不同而异。当恒定聚合物浓度时，添加剂的用量对膜形态结构有很大的影响，但孔的大小及多少与添加剂含量的多少不成正比。     

NH_4Cl水溶液在成膜过程中的致孔作用

本文以ＮＨ４Ｃｌ饱和水溶液做添加剂，对ＰＶＤＦ／ＮＭＰ体系在成膜过程中的致孔作用做了研究。铸膜液中随ＮＨ４Ｃｌ水溶液加入量的改变，膜孔径也发生变化，并出现最大值。通过Ｘ－射线衍射扫描发现制膜液中存在无机盐时膜中无定形态结构增加，表明无机盐的加入有助于膜孔形成     

液相添加剂对PTCR陶瓷电性能的影响

液相添加剂ＡＳＴ（Ａｌ２Ｏ３＋ＳｉＯ２＋ＴｉＯ２）对ＢａＴｉＯ３陶瓷材料电性能的影响很大，随着Ａｌ２Ｏ３含量的增加，材料的电性能降低；ＳｉＯ２、ＴｉＯ２的物理特性对材料电性能影响较大；过量ＴｉＯ２对材料ＰＴＣ效应有重要影响，适当过量ＴｉＯ２含量，可得到性能优良的ＰＴＣＲ陶瓷。