Asymmetric alumina membranes electrochemically formed in oxalic acid solution

Alumina membranes were fabricated by anodizing aluminium metal in 0.15 M oxalic acid. The growth kinetics of the porous layer were investigated in the temperature range –1 to 16 °C using linear potential scans up to 70 V. The faradaic efficiencies of metal oxidation and of porous layer formation, determined by applying Faraday's law, were found to be independent of both temperature and electrical charge. SEM analysis of the metal-side and solution-side surfaces revealed different morphologies. After dissolution of the barrier layer in phosphoric acid, the metal-side surface showed circular pores whose size of about 90 nm was found to be uniform and independent of temperature. The pore population was also practically independent of temperature and a value of about 4 × 10¹³ pores m^–2 was determined. On the solution-side surface the presence of a deposit partially occluding the mouths of pores was observed. This coating could be removed by chemical etching in NaOH or thermal treatment at 870 °C, where decomposition of oxalate occurs. This supports the hypothesis that the deposit consists of an aluminium salt containing oxalate anions precipitated from the solution. The results show that it is possible to control the morphological characteristics of the anodic alumina membranes by careful choice of experimental conditions.     

Two dimensional deformation characteristics of bloom CC with liquid core reduction

A two-dimensional model was applied to simulate the liquid core reduction(LCR) technology of bloom CC using ANSYS software.The deformation characteristics of bloom under different liquid fraction and reducing amount are obtained.The results indicate that the main deformation condition of bloom shell is compressive strain,mainly undertaken by the liquid core,which increases with the enhancement of reducing amount.Solidified shell takes minor deformation.The longitudinal section of bloom appears sunken and the narrow side bulges,which grow serious when the liquid fractionincreases.     

高合金铁基烧结材料在轧钢导位中的应用研究

本文研究了高合金铁基烧结材料在轧钢导位中的应用。实验表明,通过粉末冶金液相烧结技术,可以获得具有优良综合性能的制品,材料密度ρ≥7.5 g/cm3,硬度≥55 HRC,抗弯强度≥1 000 MPa,冲击韧度αk≥3.9 J/cm2,满足了轧钢导位辊的工作要求。材料利用率可达95%以上、降低了制备成本。使用寿命是普通轧辊寿命的3~6倍,适用于线材和小型型材的轧钢生产。     

铸件浸渗系统脱液机故障树的建立和分析

利用FTA方法对脱液机的各种故障进行系统分析,建立了脱液机的故障树,并对故障树进行定性分析.找出了影响脱液机可靠性的主要因素,提出了提高脱液机可靠性的相应措施.     

甲烷氧化偶联中钙钛矿催化膜的研究进展

甲烷氧化偶联对充分利用天然气资源具有非常重要的意义 ,以钙钛矿催化膜为核心的催化技术最有希望实现这一过程的工业化。本文介绍了近几年来人们对钙钛矿催化膜的研究成果 ,指出了这一领域今后的发展重点。     

固液相变蓄能的数学模型和自然对流换热系数的实验研究

引入自然对流换热系数 ,将固液蓄能数学模型简化为仅用能量方程加以描述。并通过实验测得相变过程的实际温度场 ,证明了自然对流固液相变换热的影响不可忽略 ,验证了固液相变界面移动速率随自然对流换热系数的增大而增大的定性关系     

Liquid crystalline polymers as additives to enhance the device properties of low molecular mass liquid crystals

Magnetic and electric fields have been used to determine the splay (k₁₁) and bend (k₃₃) elastic constants in a series of polymer/monomer liquid crystal solutions using the well known Freedericksz transition technique. Measurements have been carried out as a function of concentration and temperature. The polymer used was a smectogenic polysiloxane side chain liquid crystal with both cyanobiphenyl and benzoate ester side groups. The monomeric solvent was the nematogen 4-n-pentyl-4′-cyanobiphenyl. All of the solutions studied were nematogenic up to a concentration of 40% w/w. It has been shown that k₁₁, k₃₃ and $\text{k}{}_{33}\text{k}{}_{11}$ all decrease with increasing polymer concentration and that at high enough concentrations $\text{k}{}_{33}\text{k}{}_{11}$ tends to become independent of temperature. The implications of these results are discussed in terms of the performance of the most common liquid crystal display, i.e. the twisted nematic device.     

Studies on chitin 3—effect of coagulants and annealing on the preparation and the properties of chitin membrane

Chitin membrane was prepared by casting a N,N-dimethyl acetamide, N-methyl 2-pyrrolidone and lithium chloride (DMA-NMP-LiCl)solution of chitin and coagulating with several media. The effect of the coagulants on membrane formation was studied. 2-Propanol was found to be more favourable than methanol, ethanol, acetone and mixtures of 2-propanol and water. The membrane obtained in 2-propanol was subjected to annealing. Annealing made the membrane dense and strong. The tensile strength of the membrane annealed at 145°C for 2hr was about twice that of an unannealed membrane. The solute permeability of the annealed membranes was lower than that of the original one. These phenomena could be clearly interpreted in terms of crystallinity.     

利用液晶光阀实现的光学形态变换

提出了基于液晶光阀的光学二值图像领域处理器，利用它完成了扩、蚀和边缘检测等形态变换操作，并给出了实验结果。