Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

Kinetics of hydantoin formation

The reaction of lignite in a slagging gasifier produces reactants which in turn form 5,5-dimethylhydantoin (DMH) as a major constituent in the condensate water. Variations in plant operating conditions made it impossible to accurately study the kinetics of formation of DMH in the actual gasifier water, and thus a model system was chosen. The reaction of acetone cyanohydrin in the presence of excess ammonium carbonate at concentrations approaching those obtained in the condensate water were studied at 50,70, and 90 °C. Secondorder kinetics were obeyed, and the pseudo second-order rate constants at the respective temperatures were 1.86, 3.6, and 4.62 dm³ mol^{? 1} h^{? 1}. Independent variation of the concentration of either acetone, cyanide, ammonia or carbonate gave results consistent with the interpretation that the formation of DMH is first order in all reactants: rate of formation of DMH = k[acetone][HCN][NH₃][CO₂]. The pseudo second-order rate constant is a complex rate constant including several rapid equilibria. A mechanism consistent with the kinetic data is presented.     

Precision equipment for symmetrical bending— Part 1. The loading system

The design and performance of precision bending equipment for testing straight beams with constant rectangular section under a pure bending moment is described. Part 1 deals with the loading arrangements and Part 2 with the rig for measuring beam deflection. The methods for recording deflection of strain gauges applied on the beam have been described elsewhere.^1–4
The reactions to the deadweight gravity loads are taken via ball bearings. The total bending moment inaccuracy, i.e. the sum of estimated systematic errors and random errors, the latter expressed as the 2Ga confidence interval about the mean (2G_cim), is about ± 25 x. 10^-4%, for 23 tests with a steel beam with 15 mm × 75 mm cross sectional dimensions, loaded to 1-1.5 mm/m strain.
The measuring rig stands on the beam via hardened and polished spherical segment feet and uses a capacitive transducer system with less than 5nm resolution. Various application tasks are described. The total inaccuracy of the measured deflection, i.e. apart from bending moment inaccuracy, is about ± 35 times 10^4% for about 10 reproduced, not repeated, tests with the same steel beam. The deflection for such a beam is of the order of 2 to 4 mm.     

Model Validation for Bridge-Road-Vehicle Dynamic Interaction System

The dynamic response of highway bridges subjected to moving truckloads has been observed to be dependent on (1) dynamic characteristics of the bridge; (2) truck configuration, speed, and lane position on the bridge; and (3) road surface roughness profile of the bridge and its approach. Historically, truckloads were measured to determine the load spectra for girder bridges. However, truckload measurements are either made for a short period of time [for example, weigh-in-motion (WIM) data] or are statistically biased (for example, weigh stations) and cost prohibitive. The objective of this paper is to present results of a 3D computer-based model for the simulation of multiple trucks on girder bridges. The model is based on the grillage approach and is applied to four steel girder bridges tested under normal truck traffic. Actual truckload data collected using a discrete bridge WIM system are used in the model. The data include axle loads, truck gross weight, axle configuration, and statistical data on multiple presence (side by side or following). The results are presented as a function of the static and dynamic stresses in each girder and compared with code provisions for dynamic load factor. The study provides an alternate method for the development of live-load models for bridge design and evaluation.     

Experimental Investigation of FRP-Strengthened RC Beam-Column Joints

The results of a comprehensive experimental program, aimed at providing a fundamental understanding of the behavior of shear-critical exterior reinforced concrete (RC) joints strengthened with fiber reinforced polymers (FRP) under simulated seismic load, are presented in this study. The role of various parameters on the effectiveness of FRP is examined through 2/3-scale testing of 18 exterior RC joints. Conclusions are drawn on the basis of certain load versus imposed displacement response characteristics, comprising the strength (maximum lateral load), the stiffness, and the cumulative energy dissipation capacity. The results demonstrate the important role of mechanical anchorages in limiting premature debonding, and they provide important information on the role of various parameters, including: area fraction of FRP; distribution of FRP between the beam and the column; column axial load; internal joint (steel) reinforcement; initial damage; carbon versus glass fibers; sheets versus strips; and effect of transverse beams.     

Identification of photoluminescence features of an epoxy resin based on components features and curing effects

Photoluminescence features in a commercial grade cured DGEBA-based epoxy resin have been investigated with as objective to determine which of the material compounds are responsible for cured resin emissions. The origin of the bands has been approached by considering photoluminescence of base resin and hardener taken separately, of their mixture, and in the course of curing. Most of the bands observed in the cured resin could be interpreted based on those found in the components taken separately. Fluorescence of the cured resin appears dominated by two broad bands that are characteristic of the hardener and exhibits a blue shift by up to 30 nm in the course of curing which could be used for cure monitoring purpose of the investigated system. Fluorescence of the base resin is clearly detected in the resin cured with tertiary amine as catalyser. However, it is very weak if the catalyser is not added. Two phosphorescence processes have been isolated in the cured resin, one of them being related to the base resin. Finally, a chemiluminescence spectrum has been recorded in the course of curing, which has been related to either curing-related reactions or to an oxidation process.     

Alpha induced reactions on Sn: An experimental study of excitation functions and possible production pathways

In the frame of a systematic study of light ion induced threshold reactions on natural tin (Sn) excitation functions for alpha particles induced reactions are presented in a 12–38 MeV energy domain. Using a stacked foil activation method the following radioisotopes were identified: ¹¹⁶Te, ¹¹⁷Te, ¹¹⁸Te, ¹¹⁹Te, ¹²¹Te, ¹²³Te, ¹¹⁷Sb, ¹¹⁸Sb, ¹²⁰Sb, ¹²²Sb, ¹²⁴Sb, ¹²⁶Sb, ¹¹⁷Sn, ¹¹¹In. The experimental cross sections for these isotopes are presented for the first time in this energy range and a direct comparison with values calculated with the ALICE-IPPE code is discussed. Possible use of these data for production of some isotopes relevant in nuclear medicine is suggested.