Influence of chromium on the local structure and morphology of ferric oxyhydroxides

The extended X-ray absorption fine structure (EXAFS) method and transmission electron microscopy (TEM) have been used for characterizing the local structure and morphology of ferric oxyhydroxides, α-FeOOH and γ-FeOOH, with and without chromium. These ferric oxyhydroxide powders were prepared from aqueous solutions containing iron and chromium ions. Radial structural functions for iron obtained by Fe K edge EXAFS spectra showed that the linkage of structural units formed by FeO₆ octahedra in γ-FeOOH is distorted by chromium addition, while such distortion in α-FeOOH is not clearly detected. On the other hand, Cr K edge EXAFS spectra showed that the local structure around chromium does not necessarily correspond to the local structure around of iron, which is observed by Fe K edge EXAFS spectra. This suggests that the structural units containing iron and chromium are heterogeneously distributed in these ferric oxyhydroxides. The local structural information was discussed coupled with morphological features of these ferric oxyhydroxides observed by TEM.     

Impact of transient chemistry on the corrosion potential of a steam turbine disc steel

The adoption of two-shifting in coal-fired power generation (switching from on-load to off-load conditions on a daily basis and off-load for the weekend) results in regular cycling of the solution chemistry of the condensed steam on the turbine discs. A first stage investigation has been made of the effect of such chemistry cycling on the corrosion potential of the disc steel. The corrosion potential is typically about +0.05 V (SCE) in off-load chemistry (aerated pure water) and below −0.6 V (SCE) in on-load chemistry (deaerated solution containing chloride or chloride and sulphate anions). The critical observation was the sluggish response of the corrosion potential upon restoration of deaerated on-load conditions with the implication of a likely increase in pit and stress corrosion crack development.     

Effects of electrical discharge surface modification of superalloy Haynes 230 with aluminum and molybdenum on oxidation behavior

The effects of the electrical discharge alloying (EDA) process on improving the high temperature oxidation resistance of the Ni-based superalloy Haynes 230 have been investigated. The 85 at.% Al and 15 at.% Mo composite electrode provided the surface alloying materials. An Al-rich layer is produced on the surface of the EDA specimen alloyed with positive electrode polarity, whereas, many discontinuous piled layers are attached to the surface of the EDA superalloy when negative electrode polarity is selected. The oxidation resistance of the specimen alloyed with positive electrode polarity is better than that of the unalloyed superalloy, and the effective temperature of oxidation resistance of the alloyed layer can be achieved to 1100 °C. Conversely, the oxidation resistance of the other EDA specimen alloyed with negative electrode polarity is even worse than that of the unalloyed superalloy.     

雷达跟踪系统的数据显示

介绍用单片机与制导雷达显示器组成的数据显示系统的设计,并且将目标的高度以数字的形式在显示器上显示,缩短操纵员的训练时间,完成了旧系统的改造升级。     

定转子圆度智能测量装置驱动研究

本文讲述了水电站机组定转子圆度测量装置的基本原理和构成,重点阐述圆度测量装置步进电机驱动部分的电路设计及如何使用TILF2407A DSP芯片来设计驱动程序.     

Electrochemical corrosion behavior of 2A02 Al alloy under an accelerated simulation marine atmospheric environment

The corrosion behavior of 2A02 Al alloy under simulated marine atmospheric environment has been studied using mass-gain, scanning electron microscope/energy dispersive spectroscopy (SEM/EDS), laser scanning confocal microscopy, X-ray diffraction spectroscopy and localized electrochemical methods. The results demonstrate that the relationship between the corrosion induced mass-gain and the corrosion time is in accordance with the power rule. The mass-gain increases gradually during the corrosion time, while the corrosion rate decreases. With ongoing of the corrosion, corrosion products film changed from a porous to a compact structure. The various spectroscopic data show that the corrosion products films composed mainly of Al(OH)₃, Al₂O₃ and AlCl₃. The electrochemical corrosion behavior of the 2A02 Al alloy was studied by electrochemical impedance spectroscopy (EIS).     

EDA9033A在分布式风机性能测试系统中的应用

针对以单片机为核心的风机性能测试系统存在稳定性差、抗干扰能力差、精度低等问题,开发了以PLC为核心、采用互感式采集模块EDA9033A采集风机电参数的分布式风机性能测试系统,给出了该风机性能测试系统的结构,详细介绍了EDA9033A的硬件及软件设计。实际应用表明,EDA9033A采集的风机电参数结果稳定、快速、准确。     

一种基于W7100A的实验室仪器信息采集系统

针对实验室仪器信息统计中的准确性、完整性欠缺及低效率等问题,设计了一种全新的实验室仪器信息采集系统,以低功耗网络微处理器W7100A为系统的主控制器,通过SHT11温湿度传感模块和ZLG500AT射频IC模块直接采集仪器的环境参数等信息,通过用户与上位机客户端软件交互的方式采集仪器的工作内容等信息,相较于传统的手工记录方式,信息采集的及时性、完整性、可靠性方面都有了极大的提高.     

Group path covering and distance two labeling of graphs

For a positive integer d, an L(d,1)-labeling f of a graph G is an assignment of integers to the vertices of G such that |f(u)−f(v)|?d if uv∈E(G), and |f(u)−f(v)|?1 if u and u are at distance two. The span of an L(d,1)-labeling f of a graph is the absolute difference between the maximum and minimum integers used by f. The L(d,1)-labeling number of G, denoted by λd,1(G), is the minimum span over all L(d,1)-labelings of G. An L^′(d,1)-labeling of a graph G is an L(d,1)-labeling of G which assigns different labels to different vertices. Denote by the L^′(d,1)-labeling number of G. Georges et al. [Discrete Math. 135 (1994) 103-111] established relationship between the L(2,1)-labeling number of a graph G and the path covering number of Gc, the complement of G. In this paper we first generalize the concept of the path covering of a graph to the t-group path covering. Then we establish the relationship between the L^′(d,1)-labeling number of a graph G and the (d−1)-group path covering number of Gc. Using this result, we prove that and for bipartite graphs G can be computed in polynomial time.     

触摸传感器QST108与PIC单片机的接口设计

QST108为意法半导体公司生产的电容触摸传感器,具有功能强大且易操作等特点,非常适合应用在能够对用户触摸做出响应的智能控制界面中。本文重点介绍了QST108的工作方式及主要操作命令,给出了QST108与PIC单片机的接口设计以及部分程序代码。