D-HPG废水的预处理

D-对羟基苯甘氨酸制药废水 COD高 ,成分复杂。采用 Fe粉及 Fenton试剂预处理 ,COD总去除率高达98%以上。小试确定了 Fe粉加入量为 14 0 g/ L、曝气时间为 7h、Fenton法预处理 D- HPG废水的最佳反应条件 :H2 O2 质量浓度为 2 1.5 g/ L,Fe SO4 质量浓度为 3.8g/ L,氧化时间为 4 h,p H为 5     

不同预处理方法对玉米芯成分的影响

对辽宁康平和湖北襄樊产的两种玉米芯进行了原始成分分析,并分别用1%氢氧化钠、10%氨水、热水、氢氧化钠-过氧化氢溶液、1%硫酸进行处理,然后再进行成分测定,比较了不同的处理方法对玉米芯中纤维素、戊聚糖、木质素含量的影响。     

常温清洁铁系磷化液研究

为使磷化实现一级清洁生产,开发了一种用于钢铁表面涂装前处理的常温清洁铁系磷化液。该磷化液组分所有的成分均参加成膜反应生成磷化膜、水、沉渣或在磷化膜干燥过程中挥发。此磷化液不含亚硝酸盐和重金属,在5~40℃下浸渍磷化5~10 m in,在每平方米即可生成质量约为0.7 g的膜和耐CuSO4溶液点滴时间达90~140 s的彩色磷化膜。且磷化后可免水洗。     

Effect of Pretreatment Atmosphere on CuO/TiO2 Activities in NO + CO Reaction

Using TiO₂ as carrier, CuO/TiO₂ catalysts with different CuO loading were prepared by the impregnation method. The catalytic activities in NO+CO reaction were examined with a micro-reactor gas chromatography reaction system and the methods of TPR, XPS and NO-TPD. It was found that the catalytic activities were affected by pretreatment atmosphere, i.e. H₂ atmosphere > reduction–reoxidation > 10%CO/He > reaction gas (fresh sample). NO decomposition was better by low-valence Cu species than by high-valence Cu species, i.e. Cu⁰>Cu⁺>Cu²⁺. The XPS results indicated that Cu species on CuO/TiO₂ were Cu⁰, Cu⁺, normal Cu²⁺(Cu²⁺(I)) and chain-structured Cu²⁺(Cu²⁺(II)) as –Cu–O–Ti–O–. The activities of Cu²⁺(II) were much higher than that of Cu²⁺(I), but both species were very unstable in the reaction atmosphere and easily reduced by CO, which accounted for the variable activities of fresh catalysts with increasing reaction temperature. In NO+CO reaction, the redox process was a cycle of Cu⁺–Cu²⁺(I) at low reaction temperature but was a cycle of Cu⁰–Cu⁺ at high reaction temperature. As shown by NO-TPD, high catalytic activities could be attributed to the following factors, e.g. oxygen caves on the catalyst’s surface after pretreatment with H₂ and reduction–reoxidation, formation of Cu⁰ after pretreatment with H₂, and increment of Cu species dispersion and formation of Cu²⁺(II) after pretreatment with reduction–reoxidation.     

生物流化床预处理黄浦江原水中试研究

对采用悬浮填料的生物流化床原水预处理技术进行了探讨。分析了自然挂膜条件下的工艺启动过程。在8个工况条件下，流化床对污染物的去除效果。中试运行表明；在温度适谊，停留时间为60min，填料填充率为50%条件下，氨氮平均去除效率达到77.6%。氨氮的比表面去除负荷与温度线性相关。相关系数为0.911;CODMn平均去除率为6.5%。中试装置在温度10.6℃条件下，重启动需要4d，即对污染物有较好的去除效果；由于填料的完全流化，池体内溶解氧传质效率高，出水接近饱和溶解氧；进出水浊度变化不大。填料和池体本身不会积泥，不需反冲洗。     

预处理对催化剂性能的影响

优化催化剂的使用方法，能在一定程度上改善齐格勒－纳塔催化剂的活性和使用性能。不同的生产工艺结合其特点，采用不同的预处理方法，可以提高催化剂活性、改善产品的粒径分布。在工业生产中被普遍采用的方法是催化剂预络合、预聚以及单体预接触。介绍3种适合不同工艺的催化剂预处理方法，分析预处理对催化剂性能的影响及原因。     

亚麻粗纱煮漂工艺研究

亚麻粗纱优化煮漂工艺如下:(1)在100℃时,用3.5g/lNaOH碱煮30分钟;(2)在80℃时,在pH值为4.5,经30分钟完成亚漂;(3)在90℃时,pH为9的条件下处理20分钟完成氧漂;经煮漂的纱其纤维素含量提高了10.38%,果胶质、木质素、脂蜡等含量下降到了较好的水平,白度达到69.68%,大幅度改善了亚麻的纺织性能和服用性能。     

木质纤维原料预处理技术

木质纤维原料作为一种可转化为液体燃料的可再生资源,其转化利用已成为必然趋势,而木质纤维原料的预处理是利用木质生物资源生产乙醇的一个重要环节。文章阐述了木质纤维原料的常用预处理技术,并对其发展前景作了展望。     

Sulfur Versus Non-Sulfur Containing Polyimide Adhesives for Bonding Steel

Due to their superior thermal and chemical stability, polyimides are often used as adhesives in harsh environments. This study examines the effect on bond strength of thioether sulfur in the polyimide backbone. Bonds were made using steel that was believed to catalyze the oxidation of sulfur. In addition, non-sulfur containing polyimides with similar T_g were also studied for comparison. The polymer/metal interface was studied using both the T-peel and wedge tests. No apparent effect was observed in the T-peel test with steel where the T-peel strengths of non-sulfur and sulfur containing polyimides were similar. In the wedge test, however, the sulfur-containing BDSDA/ODA bonded to steel had the smallest initial crack length of 34 mm. However, the BTDA/APB bonds tested in a dry environment had the smallest crack growth. The sulfur-containing BTDA/ASD performed best of the bonds tested in a wet environment. Metal-catalyzed oxidation of sulfur was observed to take place in the steel case, but not to an extent to have a noticeable effect on peel strength.     

货架喷塑前处理工艺的选择与应用

介绍了CZ99-03(7)常温锌系磷化剂在货架上的应用,根据货架构件的特点,优化货架喷塑前处理工艺,讨论了影响磷化质量的工艺因素,提出了提高磷化效果的措施以及进一步改进磷化工艺的工艺设计。