快速评定砂浆配方对钢筋腐蚀的影响

用电化学方法测定砂浆试件中钢筋的极化电阻，并测定了砂浆的孔隙率，结果发现:砂浆的孔隙率、孔径分布与钢筋极化电阻大小有良好的对应关系。电化学方法能可靠、快速测定砂浆配合比、添加剂对钢筋腐蚀速度的影响。     

聚醚酰亚胺热焓松弛的分子量依赖关系

采用ＤＳＣ对不同分子量的聚醚酰亚胺的等温及动态热焓松弛行为进行了研究，并以ＫＷＷ方程对实验数据进行了非线性拟合。结果表明，分子量对热焓松弛的影响是由高分子端基引起自由体积的差异所致。不同分子量的聚醚酰亚胺分子具有不同数量的端基，淬冷时端基数目的差异将产生不同数量的过剩自由体积，从而影响松弛热焓及松弛速率、低分子量的聚醚酰亚胺松弛相对较快，且起始热焓高，松弛的表观活化能亦较小。     

离子注入对Cr12MoV钢表面组织结构和力学性能的影响

研究了Ｃｒ１２ＭｏＶ钢离子注入层的显微组织特征及其对表面性能的影响。结果表明，离子注入使Ｃｒ１２ＭｏＶ钢的表面硬度和耐磨性能得到显著改善，且存在着一个最佳的注入剂量，约为３×１０＾１＾７Ｎ＾＋／ｃｍ＾２左右。离了注入在Ｃｒ１２ＭｏＶ钢表面层中形成了大量细小弥散的第二相粒子，并使α－Ｆｅ晶格发生严重畸变，从而引起材料表面强化。     

ZnO陶瓷材料的负阻特性

介绍了ＺｎＯ陶瓷的负阻特性，主要研究了ＭｎＯ２掺杂和Ｎｉ２Ｏ３掺杂对ＺｎＯ陶瓷负阻特性的影响。     

铝－锂合金中δ’（Al＿3Li）沉淀相时效粗化行为及体积分数的测定

对经固溶处理的二种Ａｌ－Ｌｉ合金（１．９４ｗｔ．％Ｌｉ和２．７５ｗｔ．％Ｌｉ）的时效过程进行了研究。结果表明：δ’的生长速率遵从Ｏｓｔｗａｒｄ粗化动力学。１．９４ｗｔ．％Ｌｉ合金δ’产生于时效过程中，而２．７５ｗｔ．％Ｌｉ合金的δ’产生于时效的前期阶段。前者的表现体积分数明显大于根据相图估算的数伍，真实体积分数则与此值接近；后者的体积分数低于根据相图估算的数值，这可能归咎于δ’固相线的位置、统计学误差及Ｌｉ更易在时效过程中贫化。     

方块电阻测试中的有限元理论

介绍了用有限元方法计算半导体方块电阻四探针测试中二维点电流势场的模型并且证明了其正确性。由于有限元方法对边界没有限制，该方法为方块电阻测试中精确确定边界修正系数，更重要的是为微样品测试结构确定提供直接明了的理论依据。     

High-efficiency finishing process for metal mold by large-area electron beam irradiation

A new finishing process for metal molds by large-area electron beam (EB) irradiation is proposed in this study. In the large-area EB irradiation equipment used here, an EB with high-energy density is irradiated without focusing the beam, and so the EB with a maximum diameter of 60 mm can be used for melting or evaporating metal surface instantly. Experimental results show that the surface roughness decreases from 6 μmRz to less than 1 μmRz in just a few minutes under proper machining conditions. The corrosion resistance of metal mold surface also could be greatly improved by large-area EB irradiation. Furthermore, the surface roughness of tilting surface close to 90° could be well improved. Therefore, large-area EB irradiation method has a possibility to become a high-efficiency finishing process for metal molds.     

聚苯胺锂基润滑脂载流润滑下的摩擦学性能

制备了导电聚苯胺锂基润滑脂（简称PANI脂）和铜基银镀层材料（简称银层材料）。采用摩擦磨损试验机考察在无载流、载流及边界润滑条件下，铜基体材料（简称铜基材料）和银层材料的摩擦磨损性能。采用X射线衍射（XRD）、扫描电子显微镜（SEM）和电子能谱（EDS）对银层材料晶相及其表面磨斑形貌进行表征。结果表明，载流条件下，PANI脂润滑试验时的银层材料不仅具有良好的减摩抗磨性能，而且导电能力更强，其优异的减摩和抗磨性能归功于摩擦表面的保护膜和电流热效应引起的表面软化双重作用。     

Effect of reliability of grounding of the shaft of a turboset on the operation of devices for control and protection of exciting circuits

Disturbance of the grounding of the shaft of a turboset or its absence for technical reasons can result in failure, misoperation, limitation of the operating zone, errors or limitation of the sensitivity of devices for control and protection of exciting circuits from single-point leakage, and electroerosion of elements of the turboset structure. Measures for increasing the reliability of the grounding of the shaft are discussed. __________ Translated from élektricheskie Stantsii, No. 3, March 2006, pp. 61–66.