Influences of zinc oxide and an organic additive on the electrochemical behavior of pure aluminum in an alkaline solution

The corrosion behavior of pure aluminum in inhibited and uninhibited 4 MKOH was investigated by means of hydrogen collection, polarization curve measurement and electrochemical impedance spectroscopy (EIS). The results showed that the corrosion of pure aluminum was greatly inhibited by the addition of ZnO and dimethyl amine epoxy propane (designated as DE). EIS and EDAX analyses revealed that ZnO produces its effect by depositing on the aluminum surface, which increases the overpotential of hydrogen evolution. It was also found that the addition of DE could greatly improve the deposition of zinc layers.     

Preparation of Aluminum Nitride Powder from Aluminum Polynuclear Complexes

AIN powder was synthesized from aluminum polynuclear complexes. Basic aluminum chloride and basic aluminum lactate were used as the aluminum polynuclear complexes. These starting materials and glucose were dissolved in water and mixed homogeneously. AIN powder was obtained by calcining after drying and precalcining at 800°C under nitrogen gas flow. Then excess carbon was removed by firing in air. Nitridation in the system was investigated and compared with that in the alumina–carbon black system. It was found that in our reaction system nitridation began and proceeded at lower calcination temperatures above 1200°C than in the alumina–carbon black system. Using aluminum polynuclear complexes, AIN was synthesized through the nitridation of γ-alumina and produced in a very fine and sharp particle size distribution.     

电解法处理利福霉素SV钠废渣分离液的研究

根据电化学原理，采用电解法，利用铁屑与炭粒作电极，处理利福霉素SV钠药渣分离液，讨论各种因素对分离液污染物作效果的影响，COD去除率可达91．8％左右，脱色率可达95％左右。     

Proton diffusion in γ-manganese dioxide

Deconvolution of the electrolytic manganese dioxide (EMD) discharge curve has indicated the presence of a number of energetically different reduction processes. This has been used to determine the contribution of each reduction process to the total discharge. Using step potential electrochemical spectroscopy (SPECS), the i-t data were modelled as the sum of the discharge of the individual reduction processes. From this, A√ D for each reduction process as a function of degree of discharge was determined. The maximum A√ D values for each process ranged from 2.3×10⁻² to 4.0×10⁻⁴ cm³ s^−1/2 g⁻¹ values are consistent with previously reported values for A√ D, although in this case we have determined values for the entire compositional range.     

One-step formation of ethyl methyl ketone from 1-butene and water on ultrastable Y-type zeolite catalyst

Proton exchanged ultrastable Y-type zeolite with silica/alumina = 40 showed a pronounced catalytic activity for the formation of ethyl methyl ketone directly from 1-butene and water. The formation rate of ethyl methyl ketone was much higher than those on MoO₃-based catalysts in the oxidation of 1-butene by oxygen. It was suggested that the basic site necessary for the formation of ethyl ketone directly from 1-butene and water would be the pentacoordinated Al.     

工业纯铝在模拟海水中的电化学腐蚀行为

为研究铝在海水中的腐蚀过程,采用电化学阻抗谱、浸泡试验、扫描电子显微镜研究工业纯铝在模拟海水中的腐蚀行为.结果表明:铝在模拟海水中发生点蚀的区域为富含Fe的晶间化合物处,点蚀半径随时间的增加而扩大.铝在模拟海水中的溶解曲线分为4个区间:活性溶解区、过渡区、过钝化区、钝化区.铝在模拟海水中,极化电位为过钝化区时,转移电阻R t随着电位的升高而变小,铝发生严重的点蚀;而极化电位为钝化区时,铝的转移电阻R t随着电位的升高基本不变,铝的溶解行为受到抑制.工业纯铝在模拟海水中发生点蚀的电位区间是-0.45～-0.65 V,钝化电位区间为-0.75～-0.85 V.     

Evolution of insoluble eutectic Si particles in anodic oxidation films during adipic-sulfuric acid anodizing processes of ZL114A aluminum alloys

The effects of insoluble eutectic Si particles on the growth of anodic oxide films on ZL114A aluminum alloy substrates were in-vestigated by optical microscopy (OM) and scanning electron microscopy (SE...     

Interfacial Microstructure and Mechanical Properties of Al/Mg Butt Joints Made by MIG Welding Process with Zn-Cd Alloy as Interlayer

Butt joints between Mg alloy AZ31 B and pure Al 1 060 sheets were produced via metal inert gas welding process with Zn-Cd alloy foil. Crack-free Al/Mg butt joints between AZ31 B Mg alloy and pure Al 1060 sheets were obtained. Intermetallic compound layer 1 and layer 2 had formed in fusion zone/Mg alloy and the average thickness of the layer 1 was about 50 μm. The intermetallic compound layer 1 consisted of Al12Mg17 and Mg2Si phases while layer 2 consisted of Al12Mg17, Mg2Si and Mg Zn2 phases. The crack started from the IMC layer at the bottom of the joint and propagated along the brittle IMC layer, then expanded into weld metal during the SEM in situ tensile test. The highest tensile strength of the dissimilar metal butt joints could reach 46.8 MPa and the effect ofinterfacial IMC layer on mechanical property of the joint was discussed in detail in the present study.