激光在塑性变形测量中的应用

本文将激光应用于云纹法，研究了缺口滚压强化后根部区域的位移场及应变分布规律。结果表明，本方法是提高塑性变形测量精度的有效手段。     

Energy absorption in splitting square metal tubes

This paper presents an investigation into the energy absorbing behaviour of axially splitting square metal tubes. Tubes 50 mm square with a variable thickness were pushed slowly against rigid pyramid shaped dies, which had various semi-angles. By pre-cutting 5 mm long slits at the four corners, the tube splits along the corners and curls outward with a certain radius at a constant force. In this energy dissipating system, there are three components: tearing energy, plastic deformation energy and frictional energy. Theoretical analysis of the three energy components is presented. Curl radius is also studied in detail. Good agreement between experiments and theory is obtained. The results show that tubes which both split and curl may be used as efficient, long stroke energy absorbing devices.     

Effect of thermomechanical treatment on mechanical properties and electrical conductivity of a CuCrZr alloy

The CuCrZr alloy undergoes processes of precipitation during ageing. Besides precipitation hardening the strength is affected by cold deformation which is performed before and after ageing. The cold deformation (D ₁) before ageing accelerates the process of strength hardening, since it induces higher rate of precipitation from the saturated a-sold solution. Cold deformation (D ₂) after ageing primarily affects the alloy strength. In this paper the results of the effect of thermomechanical treatment on mechanical properties and electrical conductivity of a CuCrZr alloy are presented. The aim of the paper was to evaluate the most suitable combination of thermomechanical treatment and alloy properties.     

Failure of Al-Mg-Si alloys in bending

The bendability of two Al-Mg-Si heat-treatable alloys was studied and compared with the performance of a non-heat-treatable Al-Mg alloy. A semi-guided wrap-bend tester consistent with ASTM E290 was used to obtain minimum bend radii and produce consistent bend radii for analysis of fracture mechanisms. Bending failure in these alloys was based on a surface roughening, or orange peel, process where the outer surface grains separated and produced depressions on the surface of the material. These depressions acted as notches that increased local stresses and eventually caused failure. The fracture was intergranular in nature, with a jagged crack progressing through the thickness of the material. Several factors that affect the bendability of AA6xxx alloys are quantified in this study. Critical elements regarding natural aging, artificial aging, deformation, and composition are discussed. A parameter of specific interest is the inclusion of copper in these alloys. Copper was added in an effort to increase the artificial aging response of selected alloys. This is of particular importance in the automotive industry because artificial aging occurs during the painting process, but adequate time and temperature is not provided to fully strengthen the alloys. It is believed by some automotive manufacturers that the inclusion of copper can have a negative effect on formability and bendability.     

Buckling analysis for delaminated composites using plate bending elements based on higher‐order zig‐zag theory

A finite element based on the efficient higher‐order zig‐zag theory with multiple delaminations is developed. The bending part of the formulation is constructed from the concept of DKQ element. Unlike conventional elements, a developed element has its reference in the bottom surface which simplifies zig‐zag terms on formulation. Exact patch solutions are developed on elements which have the bottom reference system. The present element passes proper bending patch tests in the arbitrary mesh configurations in isotropic materials. Zig‐zag formulation is adopted to model laminated plates with multiple delaminations. To assess the accuracy and efficiency of the present element based on higher‐order zig‐zag theory with multiple delaminations, the linear buckling problem of laminated plates with multiple delaminations has been analysed. The results have been compared with three‐dimensional elasticity solutions. The present element works as an efficient tool for analysing the behaviour of the laminated composites with multiple delaminations. Copyright © 2002 John Wiley & Sons, Ltd.     

混凝土简支梁预设变形值探讨

以某高速公路钢筋混凝土与预应力混凝土工程为例，从简支梁的预拱度和下挠度的设置两方面进行了阐述，提出了钢筋混凝土简支梁下挠变形和预应力混凝土简支梁上拱变形的不同之处。     

碎丝埋弧焊在大型立式储罐中的应用

大型储罐底板焊接及变形控制是保证储罐整体施工质量的关键环节,采用碎丝填充的焊接方法可以防止变形,同时可以有效地避免应力集中,提高施工质量。文章介绍了碎丝埋弧焊的原理、工艺参数和焊接方法。实践证明,填充碎丝不仅是一种减小底板焊接变形的手段,同时可以充分利用焊接热能,节约焊接时间和焊剂用量,经济效益好,是一种值得推广的技术。     

Stress Concentration Factors for a Circular Hole in Curved Beams Under Bending Loads

Abstract: As a contribution to the field of stress concentration studies, the case of circular hole in curved bar elements under bending is hereby studied. Trend values of stress concentration factors (SCF) are presented based on selected variables of the problem for two critical hole locations. The results will help to identify an SCF law for practical use by applying the statistical method of regression analysis. Two approximations obtained by means of computational methods are compared with those obtained by photoelastic experimental method.     

Defect structure of gold introduced by high-speed deformation

The effect of deformation speed on defect structures introduced into bulk gold specimens at 298 K has been investigated systematically over a wide range of strain rate from ′=10⁻² to 10⁶ s⁻¹. As strain rate increased, dislocation structure changed from heterogeneous distribution, so-called cell structure, to random distribution. Also, stacking fault tetrahedra (SFTs) were produced at anomalously high density by deformation at high strain rate. The anomalous production of SFTs observed at high strain rate is consistent with the characteristic microstructure induced by dislocation-free plastic deformation, which has been recently reported in deformation of gold thin foils. Thus, the results of the present study indicate that high-speed deformation induces an abnormal mechanism of plastic deformation, which falls beyond the scope of dislocation theory. Numerical analysis of dislocation structure and SFTs revealed that the transition point of variation of deformation mode is around the strain rate of 10³ s⁻¹.     

紧凑式轧机变形规程优化设计

本文从紧凑式轧机的轧制变形特点出发,分析了其变形规程设计的主要特点和方法,讨论了限制其道次变形量的基本因素,给出了优化设计的目标函数和约束条件。指出,类似这种具有复杂约束的轧制变形问题采用混合罚函数法处理更为有效,并成功地采用该方法进行了变形规程的试设定。