参激随机共振及纠错码技术的应用

为了有效地降低数字信号传输过程中的比特误码率,提出了纠错编码与参数调节随机共振技术的结合.在经过噪声污染后,依据参数调节随机共振技术的性质,给出通过系统参数调节的二进制脉冲幅值调制（PAM）输入信号的渐近误码率公式,应用纠错码技术采用中间值估计的方法得到修正的比特误码率.数字仿真试验证实,理论计算结果与试验结果相吻合,纠错码技术与参激随机共振技术的结合应用于二进制基带信号传输,可以降低误码率,从而可以得到更好的效果,提高通信的可靠性和有效性.     

二元Al-Li合金的沉淀反应SCIEI

本文通过对两种成分的二元Al-Li合金的硬度测量,DSC分析和TEM观察,研究了其沉淀过程。实验结果表明,在恒定时间时效,合金硬度与温度的关系曲线上在低温范围内有一峰值出现;在DSC曲线低温处有明显的回溶吸热峰,因此该合金低温时效有预沉淀(富Li GP区)形成。在较高温度时效,GP区不复存在;随着δ′相颗粒长大,合金硬度很快增加;DSC曲线上有两个δ′相回溶峰,它意味着δ′析出需有两次结构调整。平衡δ相借助晶界直接从过饱和固溶体中形核长大,其热稳定性较好。     

高沸点溶剂法合成原乙酸三甲酯

对低沸点溶剂法制备原乙酸三甲酯工艺进行了改进，比较了煤油、2-乙基己醇、氯苯、异佛尔酮、邻苯二甲酸二丁酯、乙二醇二丁醚等高沸点溶剂对反应的影响，筛选出最优高沸点溶剂煤油：研究了新反应体系的醇解pH值、溶剂的循环使用次数对反应的影响及溶剂循环损耗率，结果表明，醇解的最佳pH值为5．6；随着溶剂循环次数增加，原乙酸三甲酯收率从83．6％(1次)逐渐下降到76．7％(16次)；溶剂次平均损耗率4．6％。实现了直接蒸馏产品，溶剂循环使用的新工艺。避免了旧工艺先蒸溶剂，后蒸产品，产品大量分解，收率低等缺点。     

Alternative hydrocarbon solvents for cottonseed extraction

Hexane has been used for decades to extract edible oil from cottonseed. However, due to increased regulations affecting hexane because of the 1990 Clean Air Act and potential health risks, the oil-extraction industry urgently needs alternative hydrocarbon solvents to replace hexane. Five solvents,n-heptane, isohexane, neohexane, cyclohexane, and cylopentane, were compared with commercial hexane using a benchscale extractor. The extractions were done with a solvent to cottonseed flake ratio of 5.5 to 1 (w/w) and a miscella recycle flow rate of 36 mL/min/sq cm (9 gal/min/sq ft) at a temperature of 10 to 45°C below the boiling point of the solvent. After a 10-min single-stage extraction, commercial hexane removed 100% of the oil from the flakes at 55°C; heptane extracted 100% at 75°C and 95.9% at 55°C; isohexane extracted 93.1% at 45°C; while cyclopentane, cyclohexane, and neohexane removed 93.3, 89.4, and 89.6% at 35, 55, and 35°C, respectively. Each solvent removed gossypol from cottonseed flakes at a different rate, with cyclopentane being most and neohexane least effective. Based on the bench-scale extraction results and the availability of these candidate solvents, heptane and isohexane are the alternative hydrocarbon solvents most likely to replace hexane. Presented in part at the AOCS Annual Meeting & Expo, Atlanta, Georgia, May 1994.     

Production of nanoparticles of copper compounds by anodic dissolution of copper in organic solvents

The anodic behaviour of copper was investigated in ethanol solution containing LiClO₄, LiCl electrolyte and water. The type of electrolyte and the water content influences the mechanism of the anodic process and the formation of anodic products. In LiClO₄ electrolyte the dissolution of copper is related to the oxidation of Cu(I) to Cu(II). In solutions of LiCl the etching of copper begins with the creation of soluble complexes of Cu(I) with chloride ions and solvent molecules. At potentials above 0.4 V the formation of alkoxides was observed in both solutions, characterized by a yellow tint. On the other hand, above 0.8 V (i.e. above the equilibrium potential of alcohol oxidation) copper dissolution is accompanied by the formation of a blue colloidal suspension of Cu (II) copper salt. Anodic etching of copper in solutions containing 3% H₂O at potentials higher than 0.4 V leads to the formation of colloidal suspension of copper oxide nanoparticles.     

二元混合氯化盐的配制及热物性研究

在太阳能热发电技术中,硝酸盐类相变材料是使用最多的一种相变材料,但其最高使用温度仅为600 ℃,因此找到一种热容量大、工作温度范围宽、热损失低、价格便宜的相变储热材料是目前的研究重点。选取氯化锂和氯化钠两种高温熔盐相变材料按照不同的质量比混合制备了9种二元熔盐混合物,利用差式扫描量热仪（DSC）对其在600 ℃范围内的相变温度和相变潜热进行了研究。实验结果显示：由于氯化钠的熔点较高,当氯化锂和氯化钠的二元混合物中氯化钠的含量较多时,即氯化锂的含量较少时,少量的氯化锂不能将混合物的熔点降低至600 ℃以下,混合材料无法熔化;当氯化钠和氯化锂发生熔融时,无论何种比例其相变温度均保持在540 ℃左右,浮动±15 ℃;以质量配比为90%氯化锂-10%氯化钠的二元混合物的熔融温度与结晶温度相差较大,所以该二元混合熔盐可以应用于太阳能发电的传热和蓄热技术中。     

Alternative hydrocarbon solvents for cottonseed extraction: Plant trials

Hexane has been used for decades to extract oil from cottonseed and is still the solvent of choice for the edible-oil industry. Due to increased regulations as a result of the 1990 Clean Air Act and potential health risks, the edible-oil extraction industry urgently needs an alternate hydrocarbon solvent to replace hexane. Based on laboratory-scale extraction tests, two hydrocarbon solvents, heptane and isohexane, were recommended as potential replacements for hexane. A cottonseed processing mill with a 270 MT/day (300 tons/day) capacity agreed to test both solvents with their expander-solvent process. Extraction efficiencies of isohexane and heptane, judged by extraction time and residual oil in meal, refined and bleached color of miscella refined oil, and solvent loss, were comparable to that of hexane. However, fewer problems were encountered with the lower-boiling isohexane than with the higher-boiling heptane. With isohexane, the daily throughput increased more than 20%, and natural gas consumption decreased more than 40% as compared to hexane.     

A binary approximating method for graspable region determination of biped climbing robots

For a biped pole-climbing robot (BiPCR) with grippers, it is an essential demand to determine the target grasp configuration for climbing and transiting between poles, with the graspable region as a priori knowledge. The graspable region on the target pole is critically important for climbing path planning and motion control. To efficiently compute the graspable region for a BiPCR, we propose a novel binary approximating method in this paper. This method may also be applied to generate the three-dimensional (3-D) workspace of a manipulator with constant orientation. The grasping problem and the concept of graspable region for a BiPCR are first introduced. The binary approximating method and the corresponding algorithms are then presented to generate the graspable region. Additional constraints on a biped climbing robot with five degrees of freedom (DoFs) are presented as a supplement to the algorithm. A series of comprehensive simulations are conducted with the five-DoF and six-DoF climbing robots to verify the effectiveness of the proposed method. Finally, the dexterity of biped climbing robots with different DoFs is discussed.     

折半查找算法在电子会议系统调试中的应用

关联性故障代表单元的查找定位是电子会议系统调试的关键环节。为了提高查找定位效率,提出了一种基于折半查找的快速定位算法。通过对电子会议系统中干线上的代表单元可靠度的分析,把代表单元的故障情况转化成随着代表单元数量动态变化的量化数据,构成一组有序的可靠度数据,将工程调试问题转化成数据分析问题,引入折半查找算法,设计高效准确定位故障代表单元的算法,并进行了算法效率分析。该方法操作简单,无需借助特殊工具即可应用于复杂环境下电子会议系统的现场调试。