快固化、无收缩特种MMA-R17树脂在设备基础灌浆,锚固及修补中应用

本文介绍国外聚合物砂浆的性质和应用、施工配比及物理机械性能，供设计人员参考。     

尿素熔融喷浆造粒工艺在复混肥生产中的应用

介绍了在团粒法工艺的基础上,将尿素熔融成尿液进行喷浆造粒生产复混 肥过程中存在的问题,分析产生的原因并提出改进措施,对改造效果进行了总结。     

球形磷酸铁锂材料的制备及其18650电池的测试

采用高能球磨和喷雾干燥法制备了球形磷酸铁锂材料LFP-1,并制作18650实装电池,测试电极片的压实密度,同时选择一种商业化磷酸铁锂材料LFP-2作为对比。测试结果显示,2种LFP材料均由平均粒径为300~500 nm的一次颗粒组成,比表面积为13~15 m²/g,碳质量分数为1.5%左右。通过CR2032纽扣型电池充放电测试表明,在0.2C时,LFP-1的比放电容量约为165 mA·h/g,与商业化磷酸铁锂材料LFP-2相近。制备18650电池的结果表明,商业化磷酸铁锂LFP-2材料制备的电极片的最高压实密度可以达到2.52 g/cm³,显著高于实验室制得的磷酸铁锂材料LFP-1的最高压实密度2.25 g/cm³,这可能与材料的颗粒粒度分布不同有关。     

Low-temperature methanol synthesis in a circulating slurry bubble reactor

A circulating slurry bubble reactor was developed to synthesise methanol via methyl formate from the gas mixture of carbon monoxide and hydrogen at low temperature. The strategy for designing and scaling up the bubble reactor involved a preliminary understanding of fluid dynamics in a cold model, continuous operations under industrial conditions and a parallel experiment in an autoclave. Per-pass syngas conversion was investigated during 100-h operations. The axial profile of solid catalyst concentration was measured just before the shutdown and the composition of liquid product was analysed after the shutdown. These results show that the circulating slurry bubble column will become a potential reactor for the commercial process of low-temperature methanol synthesis after the catalyst system has been improved.     

氨内参比法测定尿素熔融液中缩二脲含量

研究了尿素熔融液中缩二脲含量测定时各种消除氨干扰的方法，确定了氨内参比法可作为消除氨干扰的最佳方法，完善了该法应用时的具体操作步骤，建立了一个适用于尿素合成各工段尿液中缩二脲含量测定的简单、快速、准确的分析方法。     

旋流板塔煤浆法烟气脱硫研究

煤浆法烟气脱硫是以煤浆洗涤含二氧化硫的烟气,二氧化硫溶于浆液形成亚硫酸,煤中黄铁矿与亚硫酸、氧气发生反应,亚硫酸被氧化为硫酸,从而实现烟气脱硫.反应过程中,煤中的黄铁矿硫也被转化为硫酸而浸出,反应产生的Fe3＋/Fe2＋又对脱硫反应起到了催化剂的作用.以旋流板塔为吸收设备,研究了煤浆法烟气脱硫过程中浆液温度、液气比、空塔气速及浆液固液比等操作参数对脱硫率的影响规律.试验表明,在其他条件不变的情况下,适当提高液气比、空塔气速及浆液固液比均有利于提高脱硫效果.随着烟气脱硫过程的进行,脱硫浆液中的总铁含量不断增加,说明煤中黄铁矿被不断浸出,故此法在脱除烟气中的二氧化硫的同时也降低了煤中黄铁矿硫含量.     

离心式杂质泵蜗壳内部流场数值模拟

利用计算流体动力学分析软件,对离心式杂质泵的内部流场进行了数值模拟.计算了颗粒直径为0.076mm,固相体积分数为10%的两相流工况下的三维湍流流场,得到了蜗壳内的速度、压力和固相体积分数分布等流动信息.计算结果表明：自进口至最大半径处蜗壳内的速度不断减小,压力逐渐增大,颗粒体积分数随半径增大而增大.     

Al2O3陶瓷粉料的喷雾干燥工艺要点

本文阐述了喷雾造粒过程中的相关制备工艺 ,并通过实验总结出一套合理的工艺控制参数     

水煤浆加压气化有关堵塞问题的探讨

通过对水煤浆加压气化装置中堵塞问题的原因分析 ,提出了具体的技术改造措施 ,并从操作方法上加以改进和调整     

Reducing N losses (NH3, N2o, N2) and immobilization from slurry through optimized application techniques

In model, pot and field trials the effect of C reduced slurries and different application techniques on N losses and N immobilization were investigated. The C reduced slurries were produced by mechanical separation. Ammonia losses from surface-applied and injected cattle slurry were measured under field conditions using a wind tunnel system. Injection of slurry was the most efficient way to reduce volatilization of ammonia. After 6 days the total loss from the injected slurry was only 9% of that from surface band application. Furthermore, additional losses of N may occur through denitrification, specially after injection of slurry which may create an anaerobic environment abundant in readily oxidizable C. Therefore denitrification measurements by the acetylene inhibition technique were conducted. Until 100 days after application the loss from the injected slurry was 7.3 kg compared to 4.5 kg N ha^–1 from surface band applied slurry. After injection, denitrification was only 4.1 kg N ha^–1 for C reduced compared to 6.5 kg N ha^–1 for normal slurry. In pot trials the ammonium-¹⁵N of normal slurry and C-reduced slurry was utilized by oats between 52 and 60%, the ammonium sulfate by 67%. The increased biomass C confirmed a greater immobilization of the NH₄-N of the normal slurry resulting in a lower initial efficiency.Dedicated to Prof. Dr. A. Amberger on his 75th birthday