用有限元确定起重机裂纹补强板的参数

采用ANSYS有限元分析软件，对因出现裂纹的起重机主梁而添加的补强板进行系列计算，得出修补后主梁裂纹的应力及应力强度因子的变化规律。结果表明，采用参数适当的补强板，可降低起重机主梁裂纹尖端的应力，从而保证起重机的安全。     

剂量率对聚四氟乙烯辐射裂解的影响

本文研究了在以电子加速器的电子射线为辐射源时,剂量率对PTFE辐射裂解的影响。在剂量相同的条件下,剂量率从1.44×10~4 rad/s增至5.75×10~4 rad/s,裂解效率提高3.3倍。剂量率和各断裂参数(单位剂量裂解度a_0,G(s)值等)均成线性关系。当裂解度一定时,剂量率与剂量成反变关系。     

广西某矿区托帕石的宝石学特征

广西某矿区的脉石矿物——黄玉分三个世代,其中第三世代的黄玉晶体无色透明,重量大于0.9克拉,瑕疵不明显,密度(3.50)、硬度(7.8430)和折射率(1.6330)等特征均达宝石级,经系统研究测试,可以命名为托帕石(Topaz)。     

STM tunneling spectroscopy on high Tc superconductors

STM tunneling spectroscopy has been performed on the bulk single crystals of BiSrCaCuO (BSCCO) and the epitaxial thin films of YBaCuO (YBCO) at cryogenic temperatures. The STM images and tunneling spectra observed on the (001) surfaces can be classified into three cases; 1) Atomic image is visible. However, the tunneling spectrum shows semiconducting or smeared superconducting gap structures, depending on the tip-sample distance. 2) Clear atomic image can not be obtained. But, the tunneling spectrum shows flat bottom region with quite low zero bias conductance. 3) Tunneling spectra demonstrate gapless behavior, independent of the tip-sample separation. These observations support the quasi-2D electronic picture in whichs-wave like 2D superconducting layers are coupled with each other through the Josephson effect.     

水泥基压电复合材料的制备及极化工艺研究

采用压制成型法，首次以快硬早强的硫铝酸盐水泥为基体制备了水泥基压电复合材料。详细阐述了水泥基压电复合材料的制备过程；通过实验确定了适宜的极化条件，分析讨论了极化过程中出现漏电流的原因，并提出了一些初步的解决途径。结果表明，对硫铝酸盐水泥基压电复合材料来说，适宜的极化工艺参数：极化电场强度为4kV／mm，极化时间为45min，极化温度应低于130℃。     

贵冶动力中心二期反渗透系统改造

本文阐述对贵冶动力车间二期反渗透进行改造的成功实践 ,主要从反渗透系统设计、反渗透系统中容易出现的问题及解决方法等进行介绍。     

Optimum thermoeconomic and thermodynamic performance characteristics of an irreversible three-heat-source heat pump

The coefficient of performance and specific heating load of an irreversible three-heat-source heat pump are given by using a general cycle model affected by the finite-rate heat transfer, heat leak and internal irreversibility of the cyclic working fluid. The heat pumping load divided by the total cost per unit time is taken as a new objective function and used to investigate the performance of the heat pump. The thermoeconomic and thermodynamic performance characteristics of the heat pump are discussed in detail. Some important performance parameters such as the thermoeconomic objective function and coefficient of performance are optimized. The optimally operating regions of the heat pump and the bounds of several performance parameters are determined. Finally, it is pointed out that the Carnot heat pump may be taken as a special case of a three-heat-source heat pump and consequently its optimal performance can be directly derived from the results obtained here.     

浅议斜坡稳定性计算中水压力的作用

理论推导证明了静水压力模式与动水压力模式下地下水作用效果的差异,并且结合前人的研究成果,提出要取得合理的稳定性计算结果,两种水压力模式下所选用的强度参数应有所区分,对于静水压力模式,应取快剪或不排水剪指标;对于动水压力模式,则应取用慢剪或排水剪指标。最后采用一个具体的工程实例验证了结论的合理性。     

论工艺参数对烧结产质量的影响及分析

本文论述了正确认识烧结工艺参数对搞好烧结生产的意义，介绍了烧结工艺参数其及相互关系，详述了烧结主要工艺参数对其产质量的影响，提出了烧结工艺参数认识的几点结论性意见。     

浅谈天然彩棉织物的质量

从生产实践出发 ,阐述了彩棉纤维物理指标对彩棉纱的性能、织物的强力、色牢度及色泽的影响。