Ability of the direct wave of radar ground-coupled antenna for NDT of concrete structures

The research work presented in this paper aims at evaluating the potential of the direct wave of radar ground-coupled antennas for the on site physical characterization of concrete. According to studies highlighting the ability of radar reflected waves to characterize concrete, the potential of the direct wave is studied by systematic comparison of direct and reflected wave attenuations. Among the various features of electromagnetic waves propagating through concrete, attenuation is the most sensitive to moisture and chloride contents. In order to study the sensitivity of the direct wave to the physical condition of the concrete, laboratory experiments were conducted on concrete slabs with various porosities, water contents and chloride contamination levels.The results of this study show very satisfactory correlations between attenuations of direct and reflected waves, indicating that both waves provide similar information regarding the physical state of concrete. This correlation was confirmed on two bridges by comparison of direct wave attenuation maps with reflection attenuation maps. Therefore, radar interpretation method based on the direct wave attenuation should be able to detect, in a very fast way, physical contrasts in concrete structures and, consequently, identify probable pathological areas.     

高炉铁水含硅量的混沌局部线性预测

对莱钢1号高炉(750 m3)、临钢6号高炉(380 m3)铁水含硅量([Si])进行了混沌局部线性预测.结果表明,两 座高炉[Si]的一步预测的命中率在[Si]±0.1％的范围内均达到80.0％以上,对莱钢1号高炉(b)类样本甚至达89.1％,且预 测精度在10-2数量级,对实际生产具有很好的指导作用.     

Ce对过共晶Al—Si合金熔体粘滞性和结构的影响

研究了Ce对Al—16％Si合金熔体粘滞性的影响。结果表明：Ce的加入增加了合金熔体的粘度，且随着Ce含量的增加粘度值也增加。结合加入Ce的Al—16％Si合金氢含量的变化、凝固组织和DSC曲线研究了熔体结构的变化，分析了粘度与液态结构变化之间的关系。     

多元酚——甲醛树脂中游离酚,游离醛含量的测定

多元酚－－甲醛树脂是本院开发的热固粘接剂新产品，本文给出了这一产品技术指标中游离酚、游离醛含量的测定方法，并对方法进行了讨论。     

工业石蜡的结构分析

采用核磁共振（NMR），红外吸收光谱（IR）和色－质联用（GC－MS）方法，测定了弓弩用工业石蜡的^13C-NMR谱、反转门控^13C-NMR谱、IR光谱、气相色谱和各组分的质谱，确定了该石蜡9种主要组分及其相对含量。     

Enhancement by SO2 of initial activity for selective catalytic reduction of NO with CH3OH over \gamma-alumina

The effect of SO₂ on catalytic activity for NO reduction to N₂ by methanol in excess oxygen over $\gamma$ -alumina has been investigated. SCR activity increased initially upon exposure of a fresh $\gamma$ -alumina catalyst to SO₂ which is attributed to formation of Brønsted acid sites. Longer exposure to SO₂ leads to a decline in catalytic activity to a lower steady-state NO_x reduction activity which is independent of the SO₂ content in the feed gas.     

Analysis of the Thermal Explosion in Systems Porous Reagent–Active Gas–Solid Product

The specific features of dynamics of the thermal explosion in systems porous reagent–active gas–solid product under conditions where the heatcontent/px27732h0316n23q/xxlarge8208.gif" alt="dash" align="MIDDLE" BORDER="0">transfer and masscontent/px27732h0316n23q/xxlarge8208.gif" alt="dash" align="MIDDLE" BORDER="0">transfer regions are separated from the ambient medium are considered. In addition to the competition of heat release and heat removal, the process of initiation of exothermal chemical interaction in these systems under normal pressures depends significantly on conditions of filtration transport of the gaseous reagent. The induction and postcontent/px27732h0316n23q/xxlarge8208.gif" alt="dash" align="MIDDLE" BORDER="0">induction periods of the thermal explosion are studied. The theoretical analysis of thermalcontent/px27732h0316n23q/xxlarge8208.gif" alt="dash" align="MIDDLE" BORDER="0">explosion issues is supplemented by an experimental study of the process for the porous titanium–nitrogen–titanium nitride system.     

关于生产精制元明粉的探讨

介绍了以山西运城南风自产芒硝为原料生产精制元明粉的几种工艺,以及国内外精制元明粉的市场及生产状况.精制工艺包括化学除杂法、原料优选法、重结晶法.结果表明,精制元明粉的生产过程实质是一个除杂、提纯过程：对于钙离子含量高的原料,可采用化学除杂法;对于氯离子含量高的原料,可采用氯离子富集法、冷冻法或洗涤法;镁离子较难去除,可采用水硝洗涤、冷冻法.     

Adhesion Mechanisms of Polyurethanes to Glass Surfaces I. Structure-Property Relationships in Polyurethanes and Their Effects on Adhesion to Glass

Polyurethanes were prepared from toluene diisocyanate (TDI), 1-4-butane diol (BDO) and polycaprolactone-based triols with varying molecular weights. Among each molecular weight triol-based urethane, hard segment content was varied from 20% to 70%. Differential scanning calorimetry, tensile testing, and Iosipescu shear testing were done on all the various urethanes prepared. Thermal characterization data revealed the dependence of phase separation on hard segment content as well as on the triol molecular weight. Tensile data and Iosipescu shear data further confirmed the observations made from the DSC data. The data further indicated that phase separation can greatly improve the modulus of cross-linked segmented urethanes. Adhesion of these urethanes to glass surface was evaluated using soda-lime float glass plate. Urethane samples were cast on the air side of the glass plates and adhesion was measured in shear mode. Adhesion data indicated that in addition to hard segment content, modulus, cross-link density, and molecular weight of the triols, phase separation seems to be a major factor in controlling adhesion. Surfaces of the failed adhesion samples were also analyzed and the failure mode was found to be cohesive, in varying degree, with the different urethane systems.     

High solids content emulsions. III. Synthesis of concentrated latices by classic emulsion polymerization

Two different methods of producing bi‐ and trimodal latices of a mixture of methyl methacrylate, butyl acrylate, and small amounts of acrylic acid were tested. It is shown that a combination of concentrating blends of seed particles by semibatch reaction, followed by a nucleation of small particles plus a second semibatch phase allowed us to obtain stable latices with solids contents over 65% and viscosities of below 2500 mPa s^?1 with little coagulum formation. The key parameter in determining latex stability, coagulum formation, and viscosity appears to be the the particle size distribution, and especially its modification attributed to secondary nucleation. Because it is not possible to eliminate water‐soluble monomers from the polymerization recipe, secondary (homogeneous) nucleation must be minimized by careful addition of the free‐radical initiator and choice of monomer feed flow rates. The nucleation of the third population in the trimodal latices is best accomplished with a mixed surfactant system because renucleation by anionic surfactant alone leads to detrimental changes in the particle size distribution (PSD) resulting from excessive flocculation of particles. In addition, it was found that the viscosity of the final products was not sensitive to small changes in the ionic strength of the latex, although neutralization to a pH of 6 effectively doubles the final latex viscosity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1916–1934, 2002; DOI 10.1002/app.10513