双程放大技术在光纤放大器中的应用

双程放大技术是一种高效率、低成本的实用化放大技术。本文介绍了双程放大技术的优点及在各种放大器中的应用。     

Development of a fast neutron radiography converter using wavelength-shifting fibers

A fluorescent converter for fast neutron radiography (FNR) comprising a scintillator and hydrogen-rich resin has been developed and applied to electronic imaging. The rate of the reaction between fast neutrons and the converter is increased by thickening the converter, but its opaqueness attenuates emitted light photons before they reach its surface. To improve the luminosity of a fluorescent converter for FNR, a novel type of converter was designed in which wavelength-shifting fibers were adopted to transport radiated light to the observation end face. The performance of the converter was compared with that of a polypropylene-based fluorescent converter in an experiment conducted at the fast-neutron-source reactor YAYOI in the University of Tokyo.     

NPCDP／PET复合仿毛纤维纺丝工艺研究

应用复合纺丝方法并通过加弹、空气变形等措施使ＮＰＣＤＰ／ＰＥＴ异染异收缩纤维获得优良的毛性感。简要介绍了复合纺丝的工艺路线，讨论了纺丝温度、压力、干燥工艺、拉伸条件对可纺性的影响，并明确了变形工艺对复合纤维的影响作用。制得的ＮＰＣＤＰ／ＰＥＴ复合纤维物理力学性能符合后加工要求，织物的缓弹回复角达３０５度。     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

可变波长光纤光栅滤波器用微驱动器的研制

为了研制可调谐光纤光栅滤波器而采用拉伸装置和光纤光栅一体化的微小器件结构。实现方法是由微细加工技术加工制造一种新的波长可变光纤光栅滤波器用驱动器，该微型驱动器采用电磁式驱动，由上下两层线圈构成，每个线圈有21匝平面线圈，产生约0．2μNm的扭矩，对应光纤光栅的反射波长变化约5nm。它可应用于可谓谐光纤光栅滤波器的驱动。     

水工钢闸门聚酯玻璃钢复合防腐处理方法

水环境的恶化，使水工钢闸门腐蚀加重，传统的防腐工艺保护效果下降。聚酯玻璃钢复合防腐层的水工钢闸门防腐工艺具有使用设备少，工艺简单、防腐效果好、成本低等优点，适用于在各种水环境中作各种形式的水工钢闸门防腐，效果良好。该文结合江苏省淮海农场工程施工经验，提出了水工钢闸门聚酯玻璃钢复合防腐层结构设计、施工工艺及质量标难，为今后的推广应用提供了一定的参考依据。     

新型光电混合式电流互感器设计

设计了一种光电混合式电流互感器,它由传感头、光纤传输和光电转换器、信号处理电路和工作电源4部分组成。这种结构具有绝缘性能高、可靠性强、质量小等特点,并对误差情况进行了分析。     

Nd3+ Doped Silicate Glass Photonic Crystal Fiber with Random Hole Distributions

The fabrication of one kind of large core area Nd3 doped silicate glass photonic crystal fiber, and demonstration of the fiber's waveguidence properties were reported. This fiber owns a random air hole distribution in the cladding. The measured minimum loss of this kind of fiber is 10 dB·m-1 at 660 nm. These fibers can sustain only a single mode at least over wavelength ranging from 660 nm to 980 nm.     

Role of Specimen Geometry in the Effect of Fiber Orientation on the Thermal Conductivity of a Uniaxial Carbon-Fiber-Reinforced Aluminoborosilicate Glass-Matrix Composite

A study concerning the effect of fiber orientation on the thermal conductivity of a uniaxial carbon-fiber-reinforced borosilicate glass was conducted. For thin specimens, and thick specimens with specimen sides cut parallel to the fiber direction, the dependence of thermal conductivity on fiber orientation showed excellent agreement with theoretical behavior predicted for a composite infinite in extent. In contrast, the thermal conductivity data for rectangular thick specimens fell well below the data for the thin and angled specimens. For fiber orientation of 45° and higher, at which the heat was directed toward the side of the specimen rather than across, the thermal conductivity values showed excellent agreement with theoretical behavior predicted for a finite composite strip with insulated sides.     

热分析在PVA纤维预处理中的应用

用差热、热重法对原丝的热性能及由不同预处理方法所引起的PVA纤维的热行为变化进行了研究;并通过模拟脱水条件,用不同升温速率,求出了经不同预处理纤维的脱水反应活化能。结果表明,PVA原丝在230℃有一软化点,三种预处理都不同程度地影响了原丝的热效应变化;纤维在180～340℃主要为脱水反应;原丝及经脱水剂、O_3和O_3综合脱水剂处理的纤维,其脱水反应的表观活化能分别为:164.3kJ/mol,92.9kJ/mol,130.5kJ/mol和117.6kJ/mol。