基于ODMG—93标准的面向对象视图集成机制

模式集成多数据库系统中需要解决的关键问题之一，己存在的大多数面向多数据库系统都采用了面向对象视图机制来建立集成模式。为了满足基于ＣＯＲＢＡ的ＣＩＭＳ信息集成平台呆订成的需要，本文提出了一种基于数据库管理组ＯＤＭＧ的ＯＤＭＧ－９３标准的视图集成机制并通过一个完整的例子说明了这种视图机制在模式集成中的应用。     

湿敏半导体材料电导率计算方法的研究

结合修正了的耗尽层理论和多孔湿敏半导体的特点，本文提出了一个简单的物理模型作为ｎ型湿敏半导体特征的一级近似。描述了多孔湿敏半导体的导电机理，并给出了湿度与宏观电导率的关系。     

Growth of Fe on Si (100) at room temperature and formation of iron silicide

Low-energy electron diffraction (LEED), Auger electron spectroscopy and X-ray photoelectron spectroscopy (XPS) investigations of both the growth of an iron film on silicon (100) at room temperature and the subsequent formation of iron silicide are the subjects of this paper. An in-situ cleaned silicon (100) wafer without carbon or oxygen contamination exhibiting the known 2 × 1 reconstruction in the LEED pattern served as the substrate. Iron was deposited on this reconstructed surface at 300 K. The comparison of theoretical calculations based on three growth mechanisms with XPS data obtained with take-off angles of 0° and 50° clearly demonstrates a layer-by-layer growth of the iron film on silicon (100). At 300 K no formation of iron silicide was observed, although an interaction between iron and silicon could be detected at the interface. The formation of iron silicide was observed at annealing temperatures of 630–730 K. Quantitative XPS analysis yields the presence of FeSi₂, when the thickness is large enough. Neither the iron film on silicon nor the silicide shows any LEED pattern.     

苎麻阳离子改性的研究（三）：改性苎麻的染色机理

采用上染速率，等温吸附模型，Ｚｅｔａ电位、染料与纤维的结合力等方法从理论上研究了改性苎麻的染色机理，苎麻改性后，纤维表面的Ｚｅｔａ电位由原来的－４２ｍＶ提高到－１８ｍＶ，正电性显著增加，提高了阴离子染料对改性苎麻的亲和力，上染率高，节约染料。     

夏季面漆起泡的预防

面漆漆膜在夏季潮湿天气下成膜后3—5天，漆膜表面易形成米粒状的漆泡，针对漆泡的现象，寻找其形成的机理，根据起泡的机理采取预防面漆起泡的措施。     

Abrasion phenomena in twill tencel fabric

The abrasion characteristics of Tencel fabrics were evaluated by Martindale abrasion and laundering, and the breakdown mechanism of fibers was surveyed by scanning electron microscopy. The fabric was subjected to pad‐dry‐cure treatment with two different types of modified dimethyloldihydroxyethylene urea resins (Reaktant DH and Reaktant FC). Although the degree of dry abrasion varied with different resins, the damage exhibited by individual fibers differed little from untreated to resin‐treated; the major mechanism of abrasion was through friction, and the mechanism of fiber failure was multiple splitting and transverse cracking. In untreated Tencel, the characteristic feature of wet abrasion was massive fibrillation, and in crosslinked fabrics, the wet abrasion mechanism was through fiber slippage and slicing action, although in the Reaktant FC‐treated fabric, the wet abrasion mechanism was more through slicing than through fiber splitting. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1391–1398, 2006     

阳离子化多元醇防塌剂的研制

室内研究和现场应用表明,聚乙烯醇类防塌剂表现出较明显的增粘负效应,可引起钻井液粘度的急剧增加,严重影响其推广应用.通过金属盐催化降解和阳离子化反应,研制出了抑制性好且增粘负效应低的阳离子化改性多元醇防塌剂.考察了阳离子化试剂、反应温度、反应时间对取代度、反应效率和产品主要性能的影响,得出了阳离子化多元醇防塌剂最佳制备条件,即：PVA与阳离子化试剂物质的量比为1：1,反应温度为50℃,反应时间为4 h,阳离子度可达0.435.     

压裂泵往复密封性能及机理研究

根据流体动压润滑理论，对压裂泵柱塞密封摩擦副的润滑机理进行了理论分析。在排出和吸入行程，柱塞密封摩擦副均能满足流体动压润滑的条件，即在柱塞与密封界面上能形成并保持一定厚度的油膜润滑密封，从而达到减小摩擦提高寿命的目的；建立了摩擦界面油膜厚度和泄漏量的计算公式。利用有限元法理论，对密封圈的压力沿轴向的分布规律、泄漏量与压力变化关系进行了模拟计算。对往复密封圈沿轴向压力分布、泄漏量随压力变化进行了测试；试验结果表明，建立的计算模型具有较高的计算精度，揭示了压裂泵的密封机理。     

浸入凝胶法聚合物膜形成机理的研究现状

从热力学、传质动力学、相分离机制和固化过程几方面综述了浸入凝胶过程中聚合物膜形成机理的研究现状 .指出浸入凝胶成膜过程是传质交换和由传质交换引发的相分离以及其后的固化过程之间相互竞争的复杂非平衡过程 ,膜结构是上述几个过程竞争的结果     

The radiation crosslinking and scission of ethylene-propylene copolymers studied by solid-state nuclear magnetic resonance

Methyl groups from chain scission and H-crosslinks have been identified by solid-state nuclear magnetic resonance in amorphous ethylene-propylene copolymers containing 23 and 36 mole % propylene after γ-irradiation to 10 MGy at 30°C. G (scission) and G (crosslink) values determined from the n.m.r. spectra and by extraction are in agreement, which suggests that the crosslinks are not clustered. This may differ from the situation in polyethylene where there is a substantial crystalline content. G(S). G(X) and the ratio G(S)/G(X) increase with increasing propylene content of the copolymers.