Comparison of Two Drying Schedules for European Hophornbeam (Ostrya carpinifolia Scop.) Lumber

Two types of conventional kiln-drying schedules (mild and harsh) based on moisture content (MC) were compared with regard to time, drying quality, and energy cost. The results were evaluated according to the classification of the European Drying Group. Proper drying periods of mild and harsh schedules were found to be 550 and 514 h, respectively. Evaluations in terms of drying quality indicated that better results were achieved with the mild schedule, especially when comparing drying defects and final MC. From an energy efficiency point of view, the harsh schedule, by saving 36 h of drying time, reduced electricity by 594 KWh and was therefore found to be $65 more profitable in this trial.     

Stickiness, Functionality, and Microstructure of Food Powders

Three major aspects of food powder are described and discussed. Stickiness is one issue that can cause production and product handling difficulties. Stickiness has been interpreted in a number of ways and thus measured differently. Functionality of the primary (single) particles or agglomerated powders is of practical interest to the consumers. The desired quality will have to be matched or exceeded by the powder manufacturers. Finally, microstructure provides a key linkage between the production and the functionality. Its formation has impacts on both the stickiness and functionality.     

A Mass Transport Model for Drying Wood under Isothermal Conditions

Mass transport in wood during drying can have different mechanisms at different periods of drying. Depending on the current moisture content (MC) and the structure of the wood, the driving forces for the mass transport are essentially different. Above the fiber saturation point (FSP), the lumens are partially saturated and the transport of liquid (free) water occurs as a consequence of capillary action. On the other hand, below the FSP, bound water within the cell walls is conveyed by diffusion, and water vapor in the lumens moves under influence of pressures gradient. Based on these considerations, a unified model is presented that takes into account the transport of the different moisture phases. Simulation of the drying of a Norway spruce sample at 50°C from about 135 to 7% MC is carried out using the finite element method (FEM). Comparison between the simulated average MC and the experimental observations obtained from X-ray computed tomography (CT) shows reasonable agreement. Possible simplifications in the model are briefly discussed as well as some aspects of the numerical implementation. Finally, the influence of absolute permeability on the average MC is studied.     

Manufacturing Drug Loaded Chitosan Microspheres by Spray Drying: Development, Characterization, and Potential Use in Dentistry

The aim of this work was to determine specifications for spray-drying manufacturing of sustained-release drug-loaded microparticles with potential application in dentistry. Chitosan was used as the microencapsulation polymer and ketoprofen as the model drug. A 1:1 chitosan/ketoprofen suspension was spray-dried under different operating conditions. The size distribution, morphology, total drug load, and release profile of the powders were characterized. In vitro release studies were performed with the powder samples entrapped in cellulose dialysis tubes. The microparticles produced had a narrow size distribution (mean diameter ranging from 2.11 to 3.27 µm), good sphericity, and a smooth surface. In vitro release studies showed a linear drug dissolution behavior.     

Drying Characteristics of Barley Grain Dried in a Spouted-Bed and Combined IR-Convection Dryers

A study was performed to determine the drying characteristics and quality of barley grain dried in a laboratory scale spouted-bed dryer at 30, 35, 40, and 45°C and an inlet air velocity of 23 m/s^-1, and in an IR-convection dryer under an infrared radiation intensity of 0.048, 0.061, 0.073, and 0.107 W cm^-2 at an air velocity of 0.5 m/s^-1. The results show that the first, relatively short, phase of a sharp decrease in the drying rate was followed by the phase of a slow decrease. The time of barley drying depended on temperature of inlet air in a spouted-bed dryer and on radiation intensities in an IR-convection dryer. Barley drying at 45°C in a spouted-bed dryer was accompanied by the lowest total energy consumption. The average specific energy consumption was lower and the average efficiency of drying was higher for drying in a spouted-bed dryer. The effective diffusivities were in the range 2.20-4.52 × 10^-11 m² s^-1 and 3.04-4.79 × 10^-11 m²/s^-1 for barley dried in a spouted-bed and in an IR-convection dryer, respectively. There were no significant differences in kernel germination energy and capacity between the two drying methods tested.     

乳化炸药混装车水孔爆破的优越性

该文分析了应用袋装炸药装填水孔爆破产生拒爆、"冲天炮"、根底偏高和爆破效果差等问题,然而应用乳化炸药混装车装填水孔可以解决这些问题,并且爆破后具有根底平整、大块率低、毒气少和综合效益高等优点.以三峡永久船闸旁侧泄水箱涵工程和江苏田湾核电站工程为例进行了分析.     

DRYING OF GRANULAR PARTICLES IN A MULTISTAGE INCLINED FLUIDIZED BED WITH MECHANICAL VIBRATION

A mathematical model for the drying rate of granular particles in a multistage inclined fluidized bed(IFB) is presented from the standpoint of simultaneous heat and mass transfer, with taking the effect of mechanical vibration added vertically into consideration.

Steady-state distributions for the temperatures and concentrations of the particles and the heating gas, and for the moisture content of the particles are numerically calculated based on the present model. The calculated results show fairly good agreement with the experimental data, which were obtained from the drying experiments of brick particles in a three-stage IFB using comparatively low temperature air(40-60°C) as the heating gas.

It has been found within the range of the experimental conditions employed that, the mechanical vibration added vertically enhances the over-all drying rate of the particles and its effect can be considered equivalent to an increase in the air velocity.     

Energy Saving in Industrial Wood Drying Addressed by a Multiscale Computational Model: Board, Stack, and Kiln

This article proposes a multiscale computational model able to calculate energy consumption in a batch lumber kiln. A dual-scale computational model of wood drying deals with the boards/stack interaction and serves as a basis for the present work. A new module was added here that calculates heat losses through kiln walls (convection, condensation) and the energy used by each kiln component (fans, heating elements, humidifier, vacuum pump, etc.). The corresponding mathematical formulation is presented and then theoretical results are compared to those collected in an industrial vacuum kiln. As application example, the effect of air reversal, air velocity, and kiln insulation are exhibited, which depicts the great potential and prospects of this new tool for energy savings in relation to the product quality.     

Modeling Condensation and Evaporation on Fruit Surface

Rewarming of fruits and vegetables after cooling is characterized by heat and mass transfer processes, which leads commonly to condensation of water on the produce surface at temperatures below the dew point. This effect may affect the produce quality due to microbial growth at unfavorable environmental conditions. The amount of condensed water is a function of the produce surface temperature and of the surrounding conditions as air temperature, air humidity, and air flow. Under practical conditions, both the warming and the condensation are strongly affected by the packaging system used. Depending on the flow conditions close to the produce surface, parameters of heat and mass transfer under laboratory conditions were measured. A mathematical model was developed for the determination of the amount of condensed water on fruit surfaces, its reevaporation, and its total dwell time dependent on the environment air conditions. The model describes the heat and mass transfer processes on single fruits. The process of diffusion of humidity in air and proceed of surface temperature is the basis for the model.