Stability and thermophysical properties of fly ash nanofluid for heat transfer applications

Improving the performance of heat transfer fluids is altogether significant. The best approach for improving the thermal conductivity is the addition of nanoparticles to the base fluid. In the present study, specific heat, dynamic viscosity, and thermal conductivity of water-based Indian coal fly ash stable nanofluid for 0.1% to 0.5% volume concentration in the temperature range of 30 to 60°C has been investigated. To evaluate an average particle diameter of 11.5 nm, the fly ash nanoparticles were characterized with scanning electron microscopy and dynamic light scattering. Using zeta potential, the stability of nanofluid in the presence of surfactant Triton X-100 was tested. Thermal conductivity and viscosity of fly ash nanofluid increased, while specific heat decreased as volume concentration increased. The effect of temperature on the fly ash nanofluid was directly proportional to its thermal conductivity and specific heat and inversely proportional to viscosity.     

多带OFDM-UWB系统峰均功率比降低方法研究

针对多带OFDM—UWB信号存在高峰均功率比的问题，提出了利用扩展与交织降低系统信号峰均功率比的方法。该方法通过对传输数据进行正交扩展与交织，使得进入多载波调制的数据趋于高斯分布，减小了传输数据自相关函数的旁瓣峰值，降低了OFDM-UWB信号的峰均功率比。由于采用正交矩阵进行扩展，扩展前后的数据传输速率保持不变。仿真结果表明，扩展与交织可以有效地降低信号峰均功率比2-5dB左右。同时该方法还具有抗窄带干扰的鲁棒性。     

ZnO基薄膜晶体管的研究

ZnO是一种宽带隙的光电半导体材料,能应用于很多领域,如可用在压敏变阻器、声表面波器件、气敏元件、紫外光探测等。ZnO也可以作为有源层应用于薄膜晶体管(TFT)中。ZnO基薄膜晶体管具有以下突出优势:对于可见光部分平均具有80%以上的透射率,迁移率可以高达36cm2/V·s,开/关电流比大于106,可在较低温度(甚至室温)下制备。基于这些优点,ZnOTFT具有取代有源矩阵液晶显示器中常规a-SiTFT的趋势。同时对ZnOTFT的研究也推动了透明电子学的发展。本文阐述了ZnOTFT优越的电学性能,指出了其目前尚存在的不足,并对其发展前景进行了展望。     

提高催化裂化装置(FCCU)柴汽比措施

为了满足市场的需要,中石化天津分公司炼油厂根据FCCU自身特点采取了一系列提高柴汽比的措施,包括:调节反应系统和分馏的操作条件及采用MGD技术,以提高柴油产率。实施后,FCCU的柴汽比从0.5提高到0.9,创造了良好的经济效益。     

丙烯酸/α-甲基丙烯酸/丙烯酰胺共聚物智能水凝胶的合成及评价

由丙烯酸（AA）、α-甲基丙烯酸（MAA）和丙烯酰胺（AM）合成了具有很好DH敏感性和一定温度敏感性的智能水凝胶，考察了合成温度、丙烯酰胺、交联剂和引发剂用量对制备的水凝胶溶胀性能的影响。结果表明，在60℃下，单体从和MAA用量分别为100mmol和75mmol时，单体AM、交联剂和引发剂用量分别为反应物总质量的32．8％、0．2％和0．4％时，制备的水凝胶溶胀性能最好。考察了介质的离子浓度、pH值和温度对水凝胶溶胀比的影响，结果表明，离子浓度越大，水凝胶的溶胀比越小；水凝胶具有一定的DH可逆性。     

三重介质油藏干扰试井压力动态特征

在建立三重介质油藏试井解释模型的基础上，对该类油藏的干扰试井压力动态变化进行了研究；分析了井筒储存、表皮系数、窜流系数以及弹性储容比对观测井井底压力的影响。结果表明，表皮系数对观测井的井底压力没有影响，而井筒储存是否会对观测井井底压力造成影响取决于井筒储存系数的大小以及激动井和观测井之间的距离，窜流系数和弹性储容比对观测井井底压力的影响与单井试井的结果相类似。     

沙漠地区高精度地震资料处理技术

受静校正及各种类型干扰的影响,西部沙漠地区地震资料的高精度处理较东部地区有更大的难度。对准噶尔盆地中部Ⅱ区、Ⅲ区、Ⅳ区、顺托果勒等区块地震资料在振幅恢复、静校正、去除各类噪音、高精度速度分析及叠前、叠后子波处理等方面进行了大量的试验与研究,形成了较为系统的高精度地震资料处理技术,在西部不同区块地震资料处理中取得了较好的应用效果。     

Improving narrow bandgap a-SiGe:H alloys grown by hot-wire chemical vapor deposition

We have improved the electronic properties of narrow-bandgap (Tauc gap below 1.5 eV) amorphous-silicon germanium alloys (a-SiGe:H) grown by hot-wire chemical vapor deposition (HWCVD) by lowering the substrate temperature and deposition rate. Prior to this work, we were unable to grow a-SiGe:H alloys with bandgaps below 1.5 eV that had photo-to-dark conductivity ratios comparable with our plasma-enhanced CVD (PECVD) grown materials [B.P. Nelson et al., Mater. Res. Soc. Symp. 507 (1998) 447]. Decreasing the filament diameter from our standard configuration of 0.5 mm to 0.38 or 0.25 mm provides first big improvements in the photoresponse of these alloys. Lowering the substrate temperature from our previous optimal temperatures (T_sub starting at 435 °C) to at 250 °C provides additional photo-to-dark conductivity ratio increasing by two orders of magnitude for growth conditions containing 20–30% GeH₄ in the gas phase (relative to the total GeH₄+SiH₄ flow).     

新安江流域安徽省地区水环境状况分析

统计分析流域内点源污染、面源污染产生量与污染物入河量的调查监测数据,结果表明:安徽省辖新安江流域点源入河系数约为面源入河系数2~3倍,点源污染是流域内主要污染来源,但面源污染的作用不容忽视,尤其是总磷,有近2/3来自面源,相对省辖淮河、长江两流域来说,面源污染贡献率明显增大。指出流域污染防治必须综合考虑点、面源污染两个方面;在点源污染不太严重的情况下,对面源污染的治理必须引起足够的重视,才能取得实效。     

Damage Development in Gray Cast Iron under Static Deformation

The authors discuss the results of experimental investigation of structural degradation of gray cast iron at various stages of static tensile deformation. Analysis of the deformation process has revealed that damageability of a material under loading can be assessed by both a special strain parameter and scatter of hardness characteristics or a ratio of the modulus deviation to the current value of the elastic modulus. A correlation between these parameters has been established.