OP-1O丙烯酸酯的合成及其乳化特性的研究

本文对OP－10丙烯酸酯非离子反应性乳化剂的合成方法进行了研究，并对合成乳化剂的各种乳化剂性能进行了测试。经过测试和聚合实验表明，在本实验条件下，OP－10与丙烯酸可以有效地进行酯化反应，合成的OP－10丙烯酸酯有较好的聚合与乳化特性。     

金属闪光外墙乳胶漆的研制及性能研究

以丙烯酸酯及有机硅单体为原料合成了核-壳型硅丙乳液,用自制分散剂将闪光铝粉分散成水性闪光铝粉浆,并成功分散于硅丙乳液中,加入进口助剂,配制成水性金属闪光外墙乳胶漆.讨论了基料的玻璃化温度、单体的加入方式、引发剂、乳化剂、反应温度、聚合工艺和pH等对乳胶漆性能的影响.     

Low-temperature catalytic growth of carbon nanotubes under microwave plasma assistance

Various carbon nanotubes (CNTs) including aligned arrays, Y-branching and some other novel morphologies have been catalytically grown on anodic porous alumina template (APAT) and on the alumina-supported catalysts with methane (or benzene) as carbon source under microwave plasma assistance below 520 °C. The growth process could be simply operated since neither heating nor bias-voltage was applied to the catalysts or APAT. The results presented in this paper not only greatly richened the nanostructures of carbon family but also provided with a new technique path for synthesizing CNTs or some other nanostructures with the characteristics of low-temperature which has some special advantages or applications.     

聚醋酸乙烯乳液缩醛化的改性研究

本文介绍了为提高聚醋酸乙烯乳液稳定性、耐水性和防冻性而进行缩醛化改性的原理，并确定了最佳工艺条件即甲醛与聚乙烯醇的配比为０．４５～０．５０。     

新型技术用于乳状液膜法脱酚的进一步研究

本文对模拟的含酚废水,采用新型技术对乳状液膜法脱酚进行了进一步的探讨。对所采用的制乳设备———撞击流-旋转填料床对制乳率、提取设备———旋转填料床对脱酚率、破乳设备———无机微孔膜法破乳的重要参数(如透过压方式、膜孔径等对膜通量和破乳率的影响)进行了研究。并且讨论了破乳后的油相回用情况。实验结果表明:撞击流-旋转填料床的制乳效率可达99.90 %以上,脱酚率可达99%左右,且瞬间完成;膜孔径越小,破乳率越高,膜通量越小;外压内抽方式的破乳效果优于单外压方式的破乳效果。对于粒径为5～2 5 μm乳液,用膜孔径为2 .0 μm的SiC微孔膜,在外压为6 0kPa、内负压为30kPa的外压内抽破乳方式下破乳,破乳率可达96 .4 % ,膜通量可达90 0L·(m2 ·h) -1。     

Oxidative flavour deterioration of fish oil enriched milk

The oxidative deterioration of milk emulsions supplemented with 1.5 wt‐% fish oil was investigated by sensory evaluation and by determining the peroxide value and volatile oxidation products after cold storage. Two types of milk emulsions were produced, one with a highly unsaturated tuna oil (38 wt‐% of n‐3 fatty acids) and one with cod liver oil (26 wt‐% of n‐3 fatty acids). The effect of added calcium disodium ethylenediaminetetraacetate (EDTA) on oxidation was also investigated. Emulsions based on cod liver oil with a slightly elevated peroxide value (1.5 meq/kg) oxidised significantly faster than the tuna oil emulsions, having a lower initial peroxide value (0.1 meq/kg). In the tuna oil emulsions the fishy off‐flavour could not be detected throughout the storage period. Addition of 5—50 ppm EDTA significantly reduced the development of volatile oxidation products in the cod liver oil emulsions, indicating that metal chelation with EDTA could inhibit the decomposition of lipid hydroperoxides in these emulsions. This study showed that an oxidatively stable milk emulsion containing highly polyunsaturated tuna fish oil could be prepared without significant fishy off‐flavour development upon storage, provided that the initial peroxide value was sufficiently low.     

Fabrication of Porous SiC Ceramics with Special Morphologies by Sacrificing Template Method

Sacrificial template technique is widely used in producing porous materials with controlled morphologies and tailored properties. In this paper, unique templates such as filters, carbon nanotube, carbon fiber and silica were used to make porous SiC ceramic with special morphologies. Template derived porous ceramic plates, SiC nano-net, fiber-inverse and bead-inverse porous SiC ceramic were successfully prepared from the preceramic precursor, polymethylsilane (PMS). The synthesis procedures were involved with the infiltration of the templates with appropriate concentration of the preceramic polymer, their curing, pyrolysis and subsequent template removal. The synthesized porous SiC was characterized by SEM, TEM, XRD and BET methods.     

基于并查集和边缘检测模板的非理想虹膜定位

非理想虹膜图像往往存在虹膜边缘模糊、灰度变化不均匀、位置偏移及光斑干扰等问题, 这些问题的存在会在一定程度上影响虹膜内、外边界定位的准确率. 针对这个问题, 本文提出采用并查集和边缘检测模板的方法来对非理想虹膜进行内、外边界定位. 内边界定位是首先采用并查集方法完成瞳孔区域粗定位, 然后采用Hough变换对瞳孔进行精确定位; 外边界定位是先利用一系列边缘检测模板大致确定外圆的位置, 然后再依据外边界附近圆环内边缘点的密度来最终完成外边界的精确定位. 实验结果表明, 对于非理想虹膜图像, 本文方法的定位正确率和定位速度均高于其他同类方法.     

负离子乳胶漆的研究及应用进展

介绍了空气中负离子的作用、负离子乳胶漆释放负离子的原理和国内外负离子乳胶漆产品的研发进展。     

两性乳化剂体系对有机硅改性丙烯酸酯乳液合成的影响

采用新型琥珀酸类两性乳化剂(A1)与非离子乳化剂壬基酚聚氧乙烯醚(CA407)复配体系,合成了有机硅γ-甲基丙烯酰氧基丙三甲氧基硅烷(A174)改性的丙烯酸酯乳液。系统研究了两性乳化剂体系与非离子乳化剂复配比例、用量及乳化剂在种子乳液与预乳液中分布比例(R/F)E对乳液聚合及其性能的影响。研究表明:乳化剂配比m(A1)∶m(CA407)=30∶70时,乳液聚合稳定性及抗电解质稳定性较好;乳化剂用量越大,乳胶粒径越小,粒径分布越宽,乳液黏度越大,涂膜吸水率也越大;乳化剂在种子乳液与预乳液中的分布比例主要影响乳液聚合的稳定性。同时通过TEM乳胶粒形态分析及DSC涂膜的玻璃化转变温度分析认为,A174主要在乳液聚合时分布在乳胶粒表面,易水解交联。