Implementing Information Systems: Some Practical Advice and a Richer Model

Recent research suggests that implementing information systems presents considerable difficulties and that many implementations are total or partial failures. This paper argues that what both practitioners and students require are richer and more acceptable models of information systems implementation. Accordingly, case study data concerning the introduction of manufacturing resource planning (MRP II) are used to illustrate five patterns of behaviour (rites) which capture important social actions; and four components of changing psychological orientation. It is argued that appreciation of the rites and psychological developments identified here will support effective change programmes. Guidelines based on our model are provided for practitioners.     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

Non-steady-state model for kinetics of free radical polymerization, 4. Direct thermal initiation

This paper deals with the non-steady-state kinetics of direct thermal initiated polymerization. The initiation is assumed to be a bimolecular reaction of the monomer. The relationship between the radical concentration and the monomer conversion is rigorously derived. In further treatment a few very close approximations are introduced based on the fact that the number of monomer molecules reacting in the initiation step is much less than that consumed in the propagation step for a process producing high polymer, and the value of the rate constant for propagation or chain transfer is much lower than that for chain termination. Expressions for various molecular parameters, such as molecular weight distribution, number-average and weight-average degrees of polymerization, and dispersity, are given. Several numerical examples are provided.     

Geometric features of the flame propagation process for an SI engine having dual‐ignition system

Flame front surface area and enflamed volume (the volume enclosed with flame front) is theoretically analysed for a spark‐ignition engine, having cylindrical disc‐shaped combustion chamber with two spark plugs located axisymmetrically on cylinder head, between cylinder axis and cylinder wall. Spherical flame front assumption is used. A computer code is developed based on purely geometric consideration of the flame development process in combustion chamber, and is used to investigate the effects of variations of spark plugs' locations on geometric features of the flame front. A comparison has also been made with a spark‐ignition engine having one spark plug at the same location. Copyright © 2002 John Wiley & Sons, Ltd.     

Temperature and pressure effects on supercritical CO2 extraction of tomato seed oil

Tomato seed oil was extracted with supercritical carbon dioxide in a semibatch-flow extractor within the temperature range 313–343 K and the pressure range 10.8–24.5MPa. The extraction rates increased with pressure, but decreased with temperature increase because of the variation in solvent density and resultant differences in oil solubility. The fatty acid composition of the extracted oil was similar to that of soybean oil.     

A method of estimating the standard gibbs free energy of formation

Standard Gibbs free energy of formation (ΔG_f⁰), an important property needed in design calculations has been estimated using molar refraction, R_M. The linear relationships derived between ΔG_f⁰ and R_M tested with the data on 8 series of hydrocarbons at 228 compounds yielded average deviations comparable to the methods cited in recent literature. The method can be used as an alternative to the existing ones, because of its simplicity combined with reasonable accuracy.     

扑炎痛的合成新法

以水杨酸和对硝基苯酚为原料,在三氯氧磷存在下进行酯化,然后催化加氢还原硝基,最后用乙酐进行二酰化制得扑炎痛,三步收率分别为80.8％、90.4％和88.5％。     

Fractional composition of partly hydrolysed polyvinyl acetate and its compatibility with hydroxypropyl methylcellulose in aqueous solutions

Fractionation of partly hydrolysed polyvinyl acetate (PVA) was performed by warming of its aqueous solutions. The following properties of the obtained fractions were determined: viscosity, molecular weight and molecular weight distribution, surface tension, and absorbance in the IR range. The blockiness of the polymer molecules, characterized by their behaviour towards iodine-containing systems such as I₂,-H₃BO₃ and I₂,-KI, was estimated. Fractionation of the aqueous solutions of PVA by warming is based mainly on the different internal molecular structure of the separated products, i.e. on the length of the vinyl acetate blocks in the PVA molecules and, to a lesser extent, on the degree of hydrolysis and the degree of polymerization. The more blocklike are the PVA molecules, the less compatible are the polymers in the PVA-hydroxypropyl methylcellulose (HPMC)-water system. At phase separation in this sytem the PVA molecules which are not compatible with HPMC are, in the first place, those of the highest blockiness.     

Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.     

复合脱氧剂对纯净钢生产的影响

论述复合脱氧剂的一般化学特性，并以碳化硅和硅铝铁两种复合脱氧剂为例，讨论其对改善钢的质量，进行纯净钢生产的影响。