新型技术用于乳状液膜法脱酚的进一步研究

本文对模拟的含酚废水,采用新型技术对乳状液膜法脱酚进行了进一步的探讨。对所采用的制乳设备———撞击流-旋转填料床对制乳率、提取设备———旋转填料床对脱酚率、破乳设备———无机微孔膜法破乳的重要参数(如透过压方式、膜孔径等对膜通量和破乳率的影响)进行了研究。并且讨论了破乳后的油相回用情况。实验结果表明:撞击流-旋转填料床的制乳效率可达99.90 %以上,脱酚率可达99%左右,且瞬间完成;膜孔径越小,破乳率越高,膜通量越小;外压内抽方式的破乳效果优于单外压方式的破乳效果。对于粒径为5～2 5 μm乳液,用膜孔径为2 .0 μm的SiC微孔膜,在外压为6 0kPa、内负压为30kPa的外压内抽破乳方式下破乳,破乳率可达96 .4 % ,膜通量可达90 0L·(m2 ·h) -1。     

动力煤洗前干法脱粉新技术

介绍了煤炭振动流化床气力分级新技术的工作原理和特点;通过该机组在郑煤集团米村矿的应用实例,说明了该技术可实现煤炭选前0～10mm内任一粒度干法分级,从而降低动力煤洗选粒度下限,优化产品结构,减少煤泥量,提高企业经济效益。     

Phase holdup and liquid dispersion in gas-liquid-solid circulating fluidized beds

Axial and radial profiles of gas and solids holdups have been studied in agas-liquid-solid circulating fluidized bed at 140mm i.d..Experimental results indicate that the axialand radial profiles of gas and solids holdups are more uniform than those in a conventionalfluidized bed.Axial and radial liquid dispersion coefficients in the gas-liquid-solid circulating fluidizedbed are investigated for the first time.It is found that axial and radial liquid dispersioncoefficients increases with increaes in gas velocity and solids holdup.The liquid velocity has littleinfluence on the axial liquid dispersion coefficient,but would adversely affect the redial liquiddispersion coefficient.It can be concluded that the gas-liquid-solid circulating fluidized bed hasadvantages such as better interphase contact and lower liquid dispersion along the axial directionover the expanded bed.     

Estimating discharge in gravel‐bed river using non‐contact ground‐penetrating and surface‐velocity radars

Discharge measurement is a critical task for gravel‐bed channels. Under high‐flow conditions, the elevation of the riverbed changes significantly by intensive torrential flow. The stage–discharge relations commonly used for stream discharge estimation may no longer be adequate. The contact‐type velocity measuring is also subject to measurement errors and/or instrument failures by the high‐flow velocities, driftwood, stumps, and debris. This study developed a new real‐time method to estimate river discharge in gravel‐bed channels. A systematic measuring technology combining ground‐penetrating radar and surface‐velocity radar was employed. The rating curves representing the relations of water surface velocity to the channel cross‐sectional mean velocity and flow area were established. Stream discharge was then deduced from the resulting mean velocity and flow area. The proposed method was examined in a steep gravel‐bed reach of the Cho‐Shui River in central Taiwan. The estimated stream discharge during three flood events were compared to the prediction by using the stage–discharge relation and the index‐velocity method. The proposed method of this study is capable of computing reasonable values of discharge for an entire flood hydrograph, whereas the other two methods tend to produce large extrapolation errors. Moreover, when the computed discharge is used in 2D flood flow simulation, the proposed method demonstrates better performance than the commonly used stage–discharge and index‐velocity methods.     

烯（醚）醛一步法合成异戊二烯技术开发—基础理论研究进展

本文介绍了烯(醚)醛一步法合成异戊二烯技术开发中,基础理论研究工作的进展,其中包括化学热力学、化学动力学、再生烧炭本征动力学和扩散动力学等理论研究。并针对该反应特征进行了化学反应规律和流动传递规律的研究。建立了流化床反应器数模和流化床再生器数模,为工程技术开发提供理论依据。     

Fuzzy度量空间上映射的又一个不动点定理

继文献〔1〕之后证明了Fuzzy度量空间上映射的又一个不动点定理，使文献〔2〕的§1（3，4）的定理成为本文的特例。     

Unipol气相法聚烯烃液体催化剂技术进展

介绍了Unipol气相法聚烯烃工艺液体催化剂的成分、加入反应器的方式和喷嘴结构及控制催化剂液滴尺寸方法等方面的最新进展情况。     

Cocurrent downflow circulating fluidized bed (downer) reactors — A state of the art review

In the last decade, cocurrent downflow circulating fluidized bed reactors, called “downer” reactors, have been proposed as an alternative to upflow circulating fluidized bed, or “riser”, reactors. In this paper, published results on downer studies are summarized and future directions of research are recommended. Downer reactors are shown to have several distinct advantages over upflow circulating fluidized bed reactors and can potentially be used in many industrial processes, mainly due to a more uniform gas and solids flow structure compared with risers.     

螺旋齿轮塑件注塑模设计

分析了斜齿轮塑件的工艺特性,给出了实用的注塑模结构,介绍了斜齿轮注塑模各系统的结构设计,论述了模具的工作原理。该模具利用定模推出机构和推管旋转脱模机构解决了螺旋齿轮脱模难的问题。模具结构紧凑,推出可靠,安装维修操作方便,成型塑件质量好,生产效率高。     

流化床电化学反应器研究进展

流化床电化学反应器是一种三维颗粒电极反应器,以其比表面积大、传质速率高而备受关注。就流化床电化学反应器在导电机理、数学模型、结构放大以及应用领域的研究现状和进展进行了综述,阐明了该类反应器开发、设计和模型化方面存在的问题,并提出了研究方向。